System Summary PEDAGARD FC PedaGard FC is comprised of a twocomponent polyurethane evenly distributed aggregate and a twocomponent aromatic nonUV exposure or twocomponent aliphatic UV exposur ID: 824119
Download Pdf The PPT/PDF document "System Summary" is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.
System SummarySystem SummaryPEDA-GARD
System SummarySystem SummaryPEDA-GARD FCPeda-Gard FC is comprised of a two-component polyurethane evenly distributed aggregate and a two-component aromatic (non-UV exposure) or two-component aliphatic (UV exposure), tintable, polyurethane topcoat. The system offers outstanding mechanical properties, including high tensile strength, and excellent tear and Elevated pedestrian decks, walkways and ramps Stadiums Balconies and terraces Rooftop recreational areas Sustainable VOC compliant Low odor and high solids Fast cure Aliphatic topcoat provides exceptional UV resistance Provides skid and abrasion resistance Excellent chloride resistance Accomodates thermal expansion and contraction System meets ASTM C957 requirements ASTM E-108 Class A Spread of Flame rated SCAQMD compliantFC7540/FC7964 topcoat is available in a Tint Base and custom Not compatible with asphaltic compounds. Do not apply to a damp, wet or contaminated surface.For on-grade applications, substrates constructed over unvented metal decks or between-slab applications, contact the Technical Service Department.The following information is to be used as a guideline for installing W K H 3 H G D * D U G ) & 3 H G H V W U L D Q 7 U D I ¿ F & R D W L Q J 6 \ V W H P ) R U F R P S O H W H application instructions, please see the NEOGARD : D W H U S U R R ¿ Q J Systems Application Manual. , Q V W D O O D ¿ H O G V D P S O H R I D W O H D V W V T X D U H I H H W D W W K H S U R M H F W site or pre-selected area as agreed to by owner's representative, applicator and manufacturer.Apply material in accordance with manufacturers written ) L H O G V D P S O H Z L O O E H V W D Q G D U G I R U M X G J L Q J F R O R U D Q G W H [ W X U H R Q 0 D L Q W D L Q ¿ H O G V D P S O H G X U L Q J F R Q V W U X F W L R Q I R U Z R U N P D Q V K L S ' R Q R W D O W H U P R Y H R U G H V W U R \ ¿ H O G V D P S O H X Q W L O Z R U N L V F R P S O H W H G and approved by Owners representative.DescriptionTest MethodResultsTensile StrengthASTM D4121,500 psiASTM D412500%ASTM D412Tear ResistanceASTM D1004150 pliWater ResistanceASTM D4711% @ 7 daysASTM D22407479ASTM D4541400 psiThe above tested results are typical values. Individual lots may vary up to 10% from the typical value. Further technical information can be found at www.neogard.com.FC7510/FC7961 Wear CoatDescriptionTest MethodResultsTensile StrengthASTM D4122,200 psiASTM D41280%ASTM D412Tear ResistanceASTM D1004165 pliWater ResistanceASTM D471ASTM D22408490ASTM D4541400 psiTaber Abrasion, 1,000 ASTM C501The above tested results are typical values. Individual lots may vary up to 10% from the typical value. Further technical information can be found at
www.neogard.com.FC7540/FC7964 TopcoatDe
www.neogard.com.FC7540/FC7964 TopcoatDescriptionTest MethodResultsTensile StrengthASTM D4121,600 psiASTM D412100%ASTM D412Tear ResistanceASTM D1004155 pliWater ResistanceASTM D471ASTM D22408090ASTM D4541400 psiTaber Abrasion, 1,000 ASTM D406088 mgThe above tested results are typical values. Individual lots may vary up to 10% from the typical value. Further technical information can be found at www.neogard.com. ) O D V K L Q J 7 D S H À D V K L Q J W D S H Reinforcing Fabric: 86220 reinforcing fabric (Tietex T-272)Wear Coat: FC7510/FC7961 urethane coatingTopcoat for Non-UV Exposure: FC7510/FC7961 urethane Topcoat for UV Exposure: FC7540/FC7964 urethane coatingProductColorPackagingGray5- and 1-gallon kitsGray4-gallon kitFC7510-011/FC7961Light Gray4-gallon kitCharcoal Gray4-gallon kitGray6- and 3-gallon kitsFC7540-011/FC7964Light Gray6- and 3-gallon kitsCharcoal Gray6- and 3-gallon kitsTanDark Maple3-gallon kitTintable: Special Order OnlyDo not proceed with application of materials when substrate temperature is less than 40°F (4°C), if precipitation is imminent, or to a damp, unclean or frosty surface. Ambient temperature should be a minimum 40°F (4°C) and rising, and more than 5°F (3°C) above dew point. Special precautions are to be taken when above 100°F (38°C) and it may be necessary to limit material & R R U G L Q D W H Z D W H U S U R R ¿ Q J Z R U N Z L W K R W K H U W U D G H V $ S S O L F D W R U V K D O O K D Y H V R O H U L J K W R I D F F H V V W R W K H V S H F L ¿ H G D U H D I R U W K H W L P H Q H H G H G W R F R P S O H W H W K H D S S O L F D W L R Q D Q G D O O R Z W K H Y H K L F X O D U W U D I ¿ F coatings to cure adequately. . H H S S U R G X F W V D Z D \ I U R P V S D U N R U À D P H ' R Q R W D O O R Z W K H X V H R I spark-producing equipment during application and until all vapors Cleaning: Surfaces contaminated with oil or grease shall be vigorously scrubbed with a stiff bristle broom and a strong non- 8500 BioDegradable Cleaner. Thoroughly wash, clean, and dry. Areas where oil or other contaminants penetrate deep into the concrete may require Shot-Blasting: Required surface preparation method for remedial construction is also the preferred method for new construction. Mechanically prepare surface by shot-blasting to industry standard surface texture (ICRI's CSP3-4) without causing additional surface defects in substrate. Shot-blasting does not remove deep penetrating oils, grease, tar or asphalt stains. Proper cleaning procedures should be followed to ensure proper Read product labels and application instructions prior to use. Products must be mixed due to settling and are formulated to be installed as manufactured, without thinning. If thinning
is required, do not thin coating materi
is required, do not thin coating material more than 10% and only after materials are mixed. See compatible thinners and additional mixing instructions in the : D W H U S U R R ¿ Q J 6 \ V W H P V $ S S O L F D W L R Q 0 D Q X D O R U F R Q W D F W Technical Service at techservice@neogard.com.Cracks and Cold Joints: Visible hairline cracks (less than 1/16" L Q Z L G W K L Q F R Q F U H W H D Q G F R O G M R L Q W V V K D O O E H F O H D Q H G S U L P H G distance of 2" on each side of crack to yield a total thickness of routed and sealed with 70991 or 70995 sealant. Refer to Sealant S U R G X F W G D W D V K H H W I R U S U R S H U X V H D S S O L F D W L R Q D Q G M R L Q W G H V L J Q instructions. Sealant shall be applied to inside area of crack only, not applied to deck surface. Detail sealed cracks with base coat & R Q W U R O - R L Q W V 6 H D O F R Q W U R O M R L Q W V H T X D O W R R U O H V V W K D Q L Q Z L G W K with 70995 urethane sealant. Install sealants in accordance with ASTM C 1193 and manufacturer's instructions. Detail sealed M R L Q W V Z L W K E D V H F R D W P D W H U L D O D G L V W D Q F H R I R Q H D F K V L G H R I ) O D V K L Q J 7 D S H , Q V W D O O À D V K L Q J W D S H D Q G U H L Q I R U F L Q J Surface Condition: Surface shall be clean and dry prior to coating.Factors That Affect Dry Film Thickness: Volume of solids, thinning, V X U I D F H S U R ¿ O H D S S O L F D W L R Q W H F K Q L T X H D Q G H T X L S P H Q W R Y H U V S U D \ other waste are among the many factors that affect the amount of Z H W F R D W L Q J U H T X L U H G W R \ L H O G S U R S H U G U \ ¿ O P W K L F N Q H V V 7 R H Q V X U H W K D W V S H F L ¿ H G G U \ ¿ O P W K L F N Q H V V L V D F K L H Y H G X V H D Z H W P L O J D X J H W R Y H U L I \ D F W X D O W K L F N Q H V V R I Z H W F R D W L Q J D S S O L H G D G M X V W L Q J D V Q H H G H G I R U W K R V H I D F W R U V Z K L F K G L U H F W O \ D I I H F W W K H G U \ ¿ O P E X L O G Primer: Where required, thoroughly mix primer and apply at a rate of 300 sf/gal (0.33 gal/100 sf) to all concrete surfaces. Within 24 hours of application of primer, base coat must be applied. If base coat cannot be applied within 24 hours, inspect surface for contaminants, clean surface as necessary, and re-prime.Base Coat: Thoroughly mix FC7500/FC7960 base coat material and apply at a rate of 88 sf/gal (1.13 gal/100 sf, 18 wet mils), to \ L H O G G U \ P L O V ( [ W H Q G E D V H F R D W R Y H U F U D F N V D Q G F R Q W U R O M R L Q
W V Wear Coat: Thoroughly mix FC7510/F
W V Wear Coat: Thoroughly mix FC7510/FC7961 wear coat material and apply at a rate of 200 sf/gal (0.5 gal/100 sf, 8 wet mils) to distributed, into wet coating at the rate of 10 lbs/100 sf. When dry, Topcoat: Note - Depending on the application, select topcoat as required. For interior/covered applications not exposed to UV O L J K W L H V X Q O L J K W D Q G V R P H À X R U H V F H Q W O L J K W L Q J X V H X U H W K D Q H topcoat under 4a. Urethane topcoat under 4b. can be used for Thoroughly mix FC7510/FC7961 topcoat material and apply at a rate of 175 sf/gal (0.57 gal/100 sf, 9 wet mils) to yield 9 Thoroughly mix FC7540/FC7964 topcoat material and apply Note: Standard system coating thickness is 35 dry mils Summary Application TableCoatProduct1PrimerVariousVarious300N/A2BaseFC7500/FC79609:188183WearFC7510/FC79613:1200AggregateN/A10 lbs/100 sf4Top (Non-UV)FC7510/FC79613:117594Top (UV)FC7540/FC79642:11609Primer: Where required, thoroughly mix primer and apply at a rate of 300 sf/gal (0.33 gal/100 sf) to all concrete surfaces. Within 24 hours of application of primer, base coat must be applied. If base coat cannot be applied within 24 hours, inspect surface for contaminants, clean surface as necessary, and re-prime.Base Coat: Thoroughly mix FC7500/FC7960 base coat material \ L H O G G U \ P L O V ( [ W H Q G E D V H F R D W R Y H U F U D F N V D Q G F R Q W U R O M R L Q W V Topcoat: Note - Depending on the application, select topcoat as required. For interior/covered applications not exposed to UV O L J K W L H V X Q O L J K W D Q G V R P H À X R U H V F H Q W O L J K W L Q J X V H X U H W K D Q H topcoat under 3a. Aliphatic urethane topcoat under 4b can be used for interior/covered or exterior applications exposed to UV Thoroughly mix FC7510/FC7961 topcoat material and apply at a rate of 106 sf/gal (0.93 gal/100 sf, 15 wet mils) to yield 15 dry mils. Immediately broadcast aggregate at a rate of approximately 10 lbs/100 sf and backroll to encapsulate Thoroughly mix FC7540/FC7964 topcoat material and apply at a rate of 95 sf/gal (1.05 gal/100 sf, 16 wet mils) to yield 15 dry mils. Immediately broadcast aggregate at a rate of approximately 10 lbs/100 sf and backroll to encapsulate Note: Standard system coating thickness is 35 dry mils Summary Application TableCoatProduct1PrimerVariousVarious300N/A2BaseFC7500/FC79609:180203Top (Non-UV)FC7510/FC79613:110615AggregateN/A10 lbs/100 sf3Top (UV)FC7540/FC79642:195AggregateN/A10 lbs/100 sfClean all mixing and application equipment immediately after use with 7055 odorless reducer, 20653 xylene thinner, toluene, or mineral spirits. Hardened material will require mechanical means of removal. 2 E V H U Y H D O O ¿ U H D Q G K H D O W K S U H F D
X W L R Q V Z K H Q K D Q G O L Q J
X W L R Q V Z K H Q K D Q G O L Q J R U V W R U L Q J Containers of deck coating material should be stored in a cool (70°F, 21°C) area to ensure long shelf life. To prevent container rupture due W R Y H U \ K L J K W H P S H U D W X U H N H H S D Z D \ I U R P K H D W D Q G R U R S H Q À D P H V 2 E V H U Y H D O O ¿ U H D Q G K H D O W K S U H F D X W L R Q V Z K H Q K D Q G O L Q J R U V W R U L Q J Before using this product, carefully read the SDS and container labels for detailed health and safety information. This product is intended for industrial use by properly trained professional applicators only. $ I W H U F R P S O H W L R Q R I D S S O L F D W L R Q G R Q R W D O O R Z W U D I ¿ F R Q F R D W H G V X U I D F H V for a period of at least 72 hours at 75°F (23°C) and 50% R.H., or until Product Data Sheets Details Warranty Samples Maintenance Manual Application Manual Troubleshooting Manual Curing Charts Chemical Resistant Charts Color Cards DateOccurrenceTemp FR.H.Description (Describe Occurrence such as weather, area coated, change order, wind, etc.)Project InformationSystem Installed:Area:City:State:Zip:Primer (Gals)Base Coat (Gals)Intermediate Coat Topcoat (Gals)Optional Granule 1. Change Order 2 Weather Related 3. Preparation 4. Primer 5. Base Coat 6. Intermediate Coat 7. Topcoat 8. Optional Granule CoatManufacturer warrants that the physical properties of the product reported above will meet the standards and deviations of the associated ASTM test method. MANUFACTURER HEREBY EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Buyer must make its own determination of the suitability of any product for its use, whether such product is used alone or in combination with other materials. To the extent this or any of Manufacturers products is proven to be defective, Buyers sole remedy shall be limited to the replacement of such defective product, exclusive of any costs of labor. MANUFACTURER SHALL NOT BE LIABLE OR OBLIGATED FOR ANY LOSS OR CONSEQUENTIAL OR OTHER DAMAGE INCURRED DIRECTLY OR INDIRECTLY BY BUYER OR ANY OTHER PERSON OR ENTITY THAT ARISES IN ANY WAY IN RELATION TO THIS OR ANY OF MANUFACTURERS OTHER PRODUCTS. Nothing contained herein shall be construed to constitute inducement or recommendation to practice any invention covered by any patent without authority of the owner of the patent. No Applicator is or should be viewed as an employee or agent of Manufacturer. PedaGardFC-SS ksk 07062017.indd2728 Empire Central - Dallas, Texas 75235 - Phone (214) 353-1600 - Fax (214) 357-7532 - www.neogard.co