Fourrow linear recirculating ball bearing and guideway Guideway with - PDF document

1 2 Four-row linear recirculating ball bea
2 Four-row linear recirculating ball bearing and guideway Guideway with teeth on undersidePageOrdering example and ordering designation....... 3Design and safety guidelines............................... 10Accessories......................................................... 10 FeaturesFour-row linear recirculating ball bearing and guideway assembliesof these series are complete units comprising:–a carriage KWVE..B or KWVE..BKT–a guideway TKVD..ZHP with helical gear teeth on the undersideexpand on the advantages of units without teeth through:–considerably reduced fitting work–increased accuracy–simplified design and machining of the adjacent construction–reduced logistical workare available in sizes 25 and 35are of a modular concept, i.e.:–within one size, toothed guidance units can be combined with all carriage types (exception: wide W designs)can support forces from all directions and moments aboutall axesare preloadedhave high load carrying capacity and rigiditycan also be supplied as a preassembled unit for higher accuracieshave integral elastic wipers on the end faces of the carr

2 iage and sealing strips for sealing the
iage and sealing strips for sealing the carriagecan be lubricated with oil or grease–the rolling contact is relubricated by means of a lubrication connector in the end piece of the carriage–the teeth must be lubricated separately. For example, afelt gear and electronically controlled lubricator can beusedare suitable for temperatures from –10°C to +100°Care highly suitable for applications–in the handling equipment and automation technology sectors.Further information on the linear recirculating ball bearing and guideway assemblies: INA Catalogue “Monorail guidance systems” 605 “MAI 91”, INA-CD-Rmediasprofessional Toothed guideway with SB carriage k0M carriage KWVE..BSB with lateral fixing holesguideway TKVD..ZHP with helical gear teeth on the underside–tooth grade 6, right hand helical teeth 19º31hardened and ground, mesh angle 20° Toothed guideway with H carriage k0M carriage KWVE..BH with fixing holes for screw mounting from aboveguideway TKVD..ZHP with helical gear teeth on the underside–tooth grade 6, right hand helical teeth 19º31hardened and ground, mesh angle 20° KUVE..B SB Z

3 HP172 858 KUVE..B H ZHP173 145 3 Orderin
HP172 858 KUVE..B H ZHP173 145 3 Ordering example and ordering designationStandard manufacturing lengths: see page4, footnotes 4)5)Guideway identical to standard manufacturing length; start and end of guideway cut obliquelyOrdering designation: KUVE25BSBZHPW2V2/1500 (Figure1).Even with n , the individual sections of the guideways have obliquely cut ends.Guideway smaller than standard manufacturing length; start and end of guideway cut obliquelyOrdering designation:KUVE35BSZHPW1V1/1400 (Figure2).Guideway larger than standard manufacturing length; start and end of guideway cut straight, joints in guideways cut obliquelyOrdering designation: KUVE25BHZHPW2V2/2700 (Figure3).Figure 1 ·Ordering example and ordering designation – endsof guideway obliqueFigure 2 ·Ordering example and ordering designation – endsof guideway straightFigure 3 ·Ordering example and ordering designation – jointsin guideways oblique, ends straightFour-row linear ball bearing and guideway KUVE..BSize25Carriage for screw mounting from sideSBGuideway with teeth on undersideZHPNumber of carriages per unitW2Carriage prelo

4 adV2Guideway length1500mmFour-row linear
adV2Guideway length1500mmFour-row linear ball bearing and guideway KUVE..BSize35Narrow carriageSGuideway with teeth on undersideZHPNumber of carriages per unitW1Carriage preloadV1Guideway length1400mmFour-row linear ball bearing and guideway KUVE..BSize25High carriageHGuideway with teeth on undersideZHPNumber of carriages per unitW2Carriage preloadV2Guideway length2700mm 1500 KUVE 25 B SB ZHP W2 V2/1500 173 148 1400 KUVE 35 B S ZHP W1 V1/1400 173 149 2700 KUVE 25 B H ZHP W2 V2/2700 173 147 4 Four-row linear recirculating ball bearing and guideway Guideway with teeth on undersideSeriesKUVE..BSBZHPKUVE..BSBZHP 32314161965HHTHKhbAhHhAGXBHGLocating faceMarkingDIN 71 412-A M6 172 726 Maximum length lmax of guideway; longer guideways are supplied in several sections and are marked accordingly. and a are dependent on the guideway length L.If there is a possibility of settling, the fixing screws should be secured against rotation.Toothed guideways of size 25 are manufactured in the following lengths: lmax=1500mm, 960mm, 540mm. The ends of guideways of these lengths are cut obliquely and ca

5 n be used directly for joining of guidew
n be used directly for joining of guideways.Toothed guideways of size 35 are manufactured in the following lengths: lmax=1680mm, 1120mm, 560mm.The ends of guideways of these lengths are cut obliquely and can be used directly for joining of guideways.See Figure Load directionsTeeth, centre distance and ratio to DIN3975/76. Dimension table · Dimensions in mm Unit Carriage Guideway Mounting dimensions Mounting dimensions Designation Designation Mass Designation Mass max 1 3 –0,005–0,03 kg/m KUVE 25 B SB ZHP KWVE 25 B SB 0,85 TKVD 25 ZHP 6,3 15001)4) 81,7 KUVE 35 B SB ZHP KWVE 35 B SB 1,8 TKVD 35 ZHP 14 16801)5) 110,4 19,3 Screw diameters and tightening torquesDesignationFixing screws ISO4762-12.9KUVE 25 B SB ZHPM617M824M617M617KUVE 35 B SB ZHPM841M1083M841M841 5 KUVE..BSBZHPKUVE..BSBZHP · View X (rotated 90°) LLR 172 727 JLZ 172 730 Module 1 L L R 1 5 6 7 9 1 2 4 min. max. min. max. min. max. 60,7 17,5 25,2 14,8 7,5 38,7 11,5 36,8 18,15 Load directionsKUVE..BSBZHP Load carrying capacityDesignationBasic load ratingsMoment ratingsdyn.stat.KUVE 25 B SB ZHP17,937510395395KUVE 35 B SB ZHP3872

6 146510201020 xzy 172 494 h2h2 172 872 6
146510201020 xzy 172 494 h2h2 172 872 6 Four-row linear recirculating ball bearing and guideway Toothed rack with lateral teethPageOrdering example and ordering designation....... 7Design and safety guidelines............................... 10Accessories......................................................... 10 FeaturesFour-row linear recirculating ball bearing and guideway assembliesof these series are complete units comprising:–a carriage KWVE..B or KWVE..BKT–a guideway TKVD..ZHST–a toothed rack ZHST..SVS with lateral helical teethexpand on the advantages of units without teeth through:–increased fitting possibilities–interchangeability of individual elements–considerably reduced fitting work–reduced logistical workare available in sizes 25, 30 and 35are of a modular concept, i.e.:–within one size, toothed guidance units can be combined with all carriage types (exception:wide W designs)can support forces from all directions and moments aboutall axesare preloadedhave high load carrying capacity and rigidityare supplied as a preassembled unithave integral elastic wipers on the end f

7 aces of the carriage and sealing strips
aces of the carriage and sealing strips for sealing the carriagecan be lubricated with oil or grease–the rolling contact is relubricated by means of a lubrication connector in the end piece of the carriage–the teeth must be lubricated separately. For example, afelt gear and electronically controlled lubricator can beusedare suitable for temperatures from –10°C to +100°Care highly suitable for applications–in the handling equipment and automation technology sectors.Further information on the linear recirculating ball bearing and guideway assemblies: INA Catalogue “Monorail guidance systems” 605 “MAI 91”INA-CD-Rmediasprofessional 0M carriage KWVE..B N with fixing holes for screw mounting from aboveguideway TKVD..ZHSTSVS with lateral helical teeth–tooth grade 6, right hand helical gear teeth, 19° 31 42hardened and ground, mesh angle 20° k0M carriage KWVE..B with fixing holes for screw mounting from aboveguideway TKVD..ZHSTSVS with lateral helical teeth–tooth grade 6, right hand helical gear teeth, 19° 31 42hardened and ground, mesh angle 20° KUVE..B N ZHST SVS205 037 KUVE..B ZHST SVS205

8 038 7 Ordering example and ordering des
038 7 Ordering example and ordering designationStandard manufacturing lengths: see page8, footnotes Toothed racks are only supplied with guideways.UnitOrdering designation: KUVE25BZHSTSVSW1V1/900 (Figure1).Guideway with toothed rackOrdering designation: TKVD25ZHSTSVS/2860 (Figure2).NoteThe guidance unit TKVD..ZHSTSVS is supplied ready assembled.For guideway lengths of more than 2880mm, the unit is supplied in subunits for joining for reasons of handling (theguideway and toothed rack are assembled). A mating piece is required for fitting and can be supplied on request. These fitting aids have left hand teeth.By agreement, single-piece guideways are available up to 5740mm.Figure 1 ·Ordering example and ordering designation – unitFigure 2 ·Ordering example and ordering designation – guideway with toothed rackFour-row linear ball bearing and guideway assemblyKUVE..BSize25Guideway with toothed rack with lateral helical teethTKVD25ZHSTSVSNumber of carriages per unitW1Carriage preloadV1Guideway length900mmGuideway of size 25, toothed rack with lateral helical teethTKVD25ZHSTSVSGuideway leng

9 th2860mm KUVE 25 B ZHST SVS W1 V1/900 9
th2860mm KUVE 25 B ZHST SVS W1 V1/900 900 205 039 TKVD 25 ZHST SVS/2860 2860 205 058 8 Four-row linear recirculating ball bearing and guideway Toothed rack with lateral teethSeriesKUVE..BZHSTSVS The maximum single-piece length of the toothed rack is 960mm.The maximum single-piece selling length of the toothed rack is 2860mm.By agreement, it may be possible to obtain a single-piece unit up to 5740mm. and a are dependent on the guideway length.Teeth, centre distance and ratio to DIN3975/76.If there is a possibility of settling, the fixing screws should be secured against rotation.See Figure Load directions Dimension table · Dimensions in mm Unit Carriage Guideway Mounting dimensions Mounting dimensions Designation Designation Mass Designation Mass max 1 3 –0,005–0,03 kg kg/m KUVE 25 B ZHST SVS KWVE 25 B 0,71 TKVD 25 ZHST SVS 8,5 2860 81,7 23,5 29,75 KUVE 30 B ZHST SVS KWVE 30 B 1,4 TKVD 30 ZHST SVS 15 2860 97,6 11,25 39,75 KUVE 35 B ZHST SVS KWVE 35 B 2,02 TKVD 35 ZHST SVS 19,2 2860 12,3 48,75 Screw diameters and tightening torquesDesignationFixing screws ISO4762-12.9KUVE 25 B ZHST SV

10 SM617M824M617M617KUVE 30 B ZHST SVSM841M
SM617M824M617M617KUVE 30 B ZHST SVSM841M1041M841M841KUVE 35 B ZHST SVSM841M1041M841M841 9 KUVE..B ZHSTSVSKUVE..B ZHSTSVS · View X (rotated through 90°) Ab1 JBXGAHHTHhKDIN 71412-A M6T6A334522K6B Locating faceMarking 5 h5 Hh11 205 030 L1JLZ1jLaRlLocating faceJLL3,3aLAL1max 2JB 205 031 Module 5 1 B L L R 2 L 1 4 5 5 6 1 min. max. min. max. 60,7 6,5 34,4 10,9 47,7 37,7 13,8 62,5 50,5 45,8 14,3 6,5 Load directions Load carrying capacityDesignationBasic load ratingsMoment ratingsdyn.stat.KUVE 25 B ZHST SVS17,937510395395KUVE 30 B ZHST SVS27,555970700700KUVE 35 B ZHST SVS3872146510201020 Mxyz0xM0y0zC, C0C, C0 172 341 10 Four-row linear recirculating ball bearing and guideway Guideway with teeth on underside or toothed rack with lateral teethDesign and safety guidelinesPermissible torques for toothed racksFor flank and tooth fracture loading with good grease lubrication (i.e. use of electronic lubricators or adequate manual lubrication once per day) and v=1,5m/s, S=1,0 together with a unilateral stable bearing arrangement for the pinion shaft, the torques in Table1 to 3 apply. If a feather ke

11 y connection isused, this torque must if
y connection isused, this torque must if necessary be calculated separately or checked in accordance with DIN6885-1.Permissible torques with shrink fit washer: dimension table Accessories.Fitting aids for guideways of any lengthIn order to facilitate fitting of guideways TKVD..ZHP and TKVD..ZHSTSVS of any length, mating pieces are available on request for fitting. These fitting aids have teeth running in the opposite direction.Safety specificationsThe following protective measures must be observed in Do not touch rotating parts – e.g. input and output shaft, spur gear, toothed rack etc.Do not undo the screw plugs on the gearbox.Avoid direct contact with lubricants.Pay attention to the datasheets from the lubricant and gearbox manufacturers.In the case of toothed racks ZHP and ZHSTSVS withends cut straight, there is a risk of injury due to sharpedges.AccessoriesHigh performance worm gear pair, specially intended for the new generation of threephase current and direct-current servomotorsLight metal housing for optimum heat dissipationSmooth runningInstallation in any positionRatios: i =

12 4,75; 6,75; 9,25; 14,5; 19,5; 29, 39, 5
4,75; 6,75; 9,25; 14,5; 19,5; 29, 39, 50Low backlash tooth set (backlash 2, adjustable)5 machined locating surfaces with adequately dimensioned fixing and threaded holes for stress-free mounting in all installation positions. Hardened pinion. Table 1 ·Guideway ZHP, toothed rack of module 2 Number of teeth on pinion Hardened teeth Max. torque282503027032290Table 2 ·Guideway ZHP and toothed rack ZHST of module 3 Number of teeth on pinion Hardened teeth Max. torque ZHP ZHST 20505410225304302560549030720550Table 3 ·Toothed rack ZHST of module 4 Number of teeth on pinion Hardened teeth Max. torque15670211020241150 11 Mounting positionIf the additional forces are to be fully utilised, the gearbox should be flange mounted on the largest locating surfaces.The most favourable mounting position for lubrication is achieved with a lateral or bottom-mounted worm shaft.With a top-mounted worm shaft, the drive power is reduced by approx. 10%.Flank backlashThe flank backlash ist set to the smallest possible value at the manufacturing plant. If the backlash changes after a long period of operation, i

13 t can be corrected to the specified valu
t can be corrected to the specified value by means of the eccentrically supported input shaft.LubricationThe gearboxes are filled with synthetic lubricant. The filling should be checked monthly and several times in the first weeks ofoperation.Under moderate load, the lubricant should be changed between once and four times per year (for single, double or triple shift operation).CouplingBore on the gearbox side; backlash-free tooth hub profile forpush mounting – similar to DIN5480 (Figure1, A)Bore on the motor side with annular spring elements as clamping connection (Figure1, B)Preassembled.Before fixing on the motor shaft as contact surfaces, clean and protect using a light oil film – this prevents fretting corrosion.Input shaftsHelical teeth, 19° 31 42, mesh angle 20°Ground teeth, grade 6 e 25 – similar to DIN3962/63/67Case hardened.Before assembly, clean input shafts and lightly grease or oil – this prevents fretting corrosion.Figure 1 ·Coupling 173 008 12 Input shaftsCouplingClamping connectionsInput shaft for feather key connection dG2dud1kl1L1l3l2 172 876 Input shaft for feather k

14 ey connection.Input shaft for shrink fit
ey connection.Input shaft for shrink fit washer connection. Input shaft, helical teeth · Dimensions in mm Ordering designation Mass Distance between axes Module Number of teeth Dimensions k 1i6 2 1 1 2 3 kg RITZ 02 30 50 PF 1,25 63,66 67,7 RITZ 02 30 63 PF 1,5 63,66 67,7 164,5 14,5 57,5 RITZ 02 30 50 PF 1,25 63,66 67,7 RITZ 02 30 63 KL 1,6 63,66 67,7 164,5 38,5 RITZ 03 20 50 PF 1,33 63,66 69,7 RITZ 03 20 63 PF 1,6 63,66 69,7 14,5 RITZ 03 20 50 KL 1,33 63,66 69,7 36,5 RITZ 03 20 63 KL 1,6 63,66 69,7 RITZ 04 15 63 PF 1,85 63,66 71,7 14,5 RITZ 04 16 63 KL 1,85 63,66 71,7 Input shaft for shrink fit washer connection L1d1ddbkl3 2 172 877 13 Coupling 1l2LDIN 54801D2L2DG1d1d2 172 873 Clamping connection L1d2d13L2L3 172 874 Coupling · Dimensions in mm Ordering designation Mass red Dimensions 1 2 1 2 1 2 4 1 2 Quantity Tightening torque kg kg/m KUP 65 43 119 0,4 0,799 1,25  Clamping connection · Dimensions in mm Ordering designation Mass red Dimensions 0 1 2 3 1 2 3 Quantity Tightening torque kg kg/m SPE 80 83 030 0,3 1,756 21,5  SPE 80 84 036 0,4 4,029 27,5 23,5  14 AccessoriesGearboxes Ge

15 arbox · Dimensions in mm Ordering design
arbox · Dimensions in mm Ordering designation Mass Ratio Dimensions Input shaft with feather key connection Input shaft with clamping connection 1 kg GETR 50 SCHN 95 115 PF-5 GETR 50 SCHN 95 115 KL-5 7 0,483 4,75 152 Gearbox with centre distance a=50mm DInput shaft withfeather key connectionInput shaft withclamping connectionxykr85M8 16M8 15459510013816028,3Ø10Ø40Ø1850H6P8H6Ø25h8Ø308118f1feG11008016137 15 Gearbox · Dimensions in mm Ordering designation Mass Ratio Dimensions Input shaft with feather key connection Input shaft with clamping connection 1 kg GETR 63 SCHN 130 165 PF-39 GETR 63 SCHN 130 165 KL-39 12 1,01 Gearbox with centre distance a=63mm DInput shaft withfeather key connectionInput shaft withclamping connectionxykr110M10 15M10 165211512517519531,3Ø1124,7Ø1863H6P8H6Ø28h8Ø368145f1feG113010525168 16 GearboxesCentre distance a=50mm MOTHDX115A6-64S or MOTHDX115C6-88S.Information on motors and controls: see INA publication “ALE”Other designs available by agreement.Gearbox, motor, pinion, coupling Ordering designation Motor Pinion Coupling Atlanta INA58 43 105GETR 50

16 SCHN 95/115 PF-5MOT HDX 115 ...RITZ 023
SCHN 95/115 PF-5MOT HDX 115 ...RITZ 023050 PFKUP58 43 107GETR 50 SCHN 95/115 PF-7MOT HDX 115 ...RITZ 023050 PFKUP58 43 109GETR 50 SCHN 95/115 PF-9MOT HDX 115 ...RITZ 023050 PFKUP58 43 115GETR 50 SCHN 95/115 PF-15MOT HDX 115 ...RITZ 023050 PFKUP58 43 120GETR 50 SCHN 95/115 PF-20MOT HDX 115 ...RITZ 023050 PFKUP58 43 139GETR 50 SCHN 95/115 PF-39MOT HDX 115 ...RITZ 023050 PFKUP58 43 150GETR 50 SCHN 95/115 PF-50MOT HDX 115 ...RITZ 023050 PFKUP58 83 105GETR 50 SCHN 95/115 KL-5MOT HDX 115 ...RITZ 023050 KLKUP58 83 107GETR 50 SCHN 95/115 KL-7MOT HDX 115 ...RITZ 023050 KLKUP58 83 109GETR 50 SCHN 95/115 KL-9MOT HDX 115 ...RITZ 023050 KLKUP58 83 115GETR 50 SCHN 95/115 KL-15MOT HDX 115 ...RITZ 023050 KLKUP58 83 120GETR 50 SCHN 95/115 KL-20MOT HDX 115 ...RITZ 023050 KLKUP58 83 139GETR 50 SCHN 95/115 KL-39MOT HDX 115 ...RITZ 023050 KLKUP58 43 305GETR 50 SCHN 80/100 PF-5MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 43 307GETR 50 SCHN 80/100 PF-7MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 43 309GETR 50 SCHN 80/100 PF-9MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 43 315GETR 50 SCHN 80/100 PF-15MOT HDX 92 E4-44 SRITZ 0230

17 50 PFKUP58 43 320GETR 50 SCHN 80/100 PF-
50 PFKUP58 43 320GETR 50 SCHN 80/100 PF-20MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 43 339GETR 50 SCHN 80/100 PF-39MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 43 350GETR 50 SCHN 80/100 PF-50MOT HDX 92 E4-44 SRITZ 023050 PFKUP58 83 305GETR 50 SCHN 80/100 KL-5MOT HDX 92 E4-44 SRITZ 023050 KLKUP58 83 307GETR 50 SCHN 80/100 KL-7MOT HDX 92 E4-44 SRITZ 023050 KLKUP58 83 309GETR 50 SCHN 80/100 KL-9MOT HDX 92 E4-44 SRITZ 023050 KLKUP58 83 315GETR 50 SCHN 80/100 KL-15MOT HDX 92 E4-44 SRITZ 023050 KLKUP58 83 320GETR 50 SCHN 80/100 KL-20MOT HDX 92 E4-44 SRITZ 023050 KLKUP58 83 339GETR 50 SCHN 80/100 KL-39MOT HDX 92 E4-44 SRITZ 023050 KLKUP 17 GearboxesCentre distance a=63mm MOTHDX115A6-64S or MOTHDX115C6-88S.Information on motors and controls: see INA publication “ALE”Other designs available by agreement.Gearbox, motor, pinion, coupling Ordering designation Motor Pinion Coupling Atlanta INA58 44 105GETR 63 SCHN 95/115 PF-5MOT HDX 115 ...RITZ 023063 PFKUP58 44 107GETR 63 SCHN 95/115 PF-7MOT HDX 115 ...RITZ 023063 PFKUP58 44 109GETR 63 SCHN 95/115 PF-9MOT HDX 115 ...RITZ 023063 PFKUP58 44 115GETR 63 SCHN 95

18 /115 PF-15MOT HDX 115 ...RITZ 023063 PFK
/115 PF-15MOT HDX 115 ...RITZ 023063 PFKUP58 44 120GETR 63 SCHN 95/115 PF-20MOT HDX 115 ...RITZ 023063 PFKUP58 44 139GETR 63 SCHN 95/115 PF-39MOT HDX 115 ...RITZ 023063 PFKUP58 84 105GETR 63 SCHN 95/115 KL-5MOT HDX 115 ...RITZ 023063 KLKUP58 84 107GETR 63 SCHN 95/115 KL-7MOT HDX 115 ...RITZ 023063 KLKUP58 84 109GETR 63 SCHN 95/115 KL-9MOT HDX 115 ...RITZ 023063 KLKUP58 84 115GETR 63 SCHN 95/115 KL-15MOT HDX 115 ...RITZ 023063 KLKUP58 84 120GETR 63 SCHN 95/115 KL-20MOT HDX 115 ...RITZ 023063 KLKUP58 84 139GETR 63 SCHN 95/115 KL-39MOT HDX 115 ...RITZ 023063 KLKUP58 44 205GETR 63 SCHN 130/165 PF-5MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 44 207GETR 63 SCHN 130/165 PF-7MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 44 209GETR 63 SCHN 130/165 PF-9MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 44 215GETR 63 SCHN 130/165 PF-15MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 44 220GETR 63 SCHN 130/165 PF-20MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 44 239GETR 63 SCHN 130/165 PF-39MOT HDX 142 C6-88 SRITZ 023063 PFKUP58 84 205GETR 63 SCHN 130/165 KL-5MOT HDX 142 C6-88 SRITZ 023063 KLKUP58 84 207GETR 63 SCHN 130/165 KL-7MOT HDX

19 142 C6-88 SRITZ 023063 KLKUP58 84 209GE
142 C6-88 SRITZ 023063 KLKUP58 84 209GETR 63 SCHN 130/165 KL-9MOT HDX 142 C6-88 SRITZ 023063 KLKUP58 84 215GETR 63 SCHN 130/165 KL-15MOT HDX 142 C6-88 SRITZ 023063 KLKUP58 84 220GETR 63 SCHN 130/165 KL-20MOT HDX 142 C6-88 SRITZ 023063 KLKUP 18 Design example Connecting plateGearbox with couplingView X 172 889 19 INA-Schaeffler KGLinear Technology Division66406 Homburg (Saar) · GermanyInternetwww.ina.comE-Mailinfo.linear@de.ina.comIn Germany:Telephone0180/5003872Fax0180/5003873From other countries:Telephone+49/6841/701-0Fax+49/6841/701-625Sach-Nr. 004-238-036/MAI 54 GB-D 02043 · Printed in Germany Market Information MAI 54 double row!New!Lateral gear teeth Four-row linear recirculating ball bearing andguideway assembliesGuideway with teeth on underside or toothed rack with lateral teeth For driven guideways, the four-row linear recirculating ball bearing and guideway assemblies KUVE..BZHP have been available for some time. In these series, the guideways have right hand helical teeth with a mesh angle of 20°. The teeth are aligned downwards, hardened and ground. In comparison with unit

20 s without teeth, these designs are more
s without teeth, these designs are more precise, allow significantly simpler adjacent constructions and give considerable reductions in fitting and logistical requirements.In order to increase further the potential applications of toothed guideways, the proven range has been expanded to include the series KUVE..BZHSTSVS. These units have a combination of a standard guideway TKVD with a toothed rack ZHST..SVS. Furthermore, the hardened and ground helical teeth are arranged laterally. This gives even more flexible fitting possibilities and increased free space in the design of the adjacent construction.Due to their modular design, the toothed series are suitable for all carriage types (except the wide W designs) and thus can be simply converted.The rolling element system of the guidance systems is lubricated by grease or oil. The teeth can be easily lubricated by means of felt gears and electronically controlled lubricators.The guidance systems can be used across a wide range of temperatures and are most suitable for applications in the handling equipment and automation technology secto