Attenuated Total Reflection Infrared Microscopy and Charpy Impact Tester for Analysis - PowerPoint Presentation

1. Attenuated Total Reflection Infrared Microscopy and Charpy Impact Tester for Analysis of Automotive Paint SmearsBarry K. Lavine and Undugodage Perera, Department of Chemistry, Oklahoma State University, Stillwater, Oklahoma 74078Kaan Kalkan and Linqi Zhang,, Department of Mechanical Engineering, Oklahoma State University, Stillwater, OK 74078

2. Modern Automotive Paint SystemsModern automotive paint systems (since 2000) consist of multiple layers of paint: thick clear coat over a thin color coat which in turn is over one or more thin undercoats (surfacer-primer and e-coat layer).

3. Problem StatementPaint Smears are often recovered from a crime scene where damage to a vehicle and/or injury or death to a pedestrian has occurred. Extracting lead information from a paint smear is problematic as there are no reference materials available in paint database to generate hit-lists of potential suspect vehicles.A procedure based on a Charpy impact tester is currently being developed to generate paint smears due to paint transfer from an automotive substrate to any surface of interest under conditions simulating those of a real collision.

4. Paint SmearsAutomotive paint smears are difficult to create in a laboratory and have also proven challenging to analyze because of the mixing of the various automotive paint layers.Because the smeared paint in all likelihood undergoes melting due to the heat generated by the impact, a separation phenomenon may occur due to differences in viscosities and/or affinities for the substrate by specific layers.

5. Charpy Impact TesterA controlled weight pendulum is swung from a set of heights (see Figure b in next slide)Subsequently, it strikes a standard notched specimen supported at both ends on an anvil, fracturing it (see Figure c-e in next slide)The amount of energy absorbed by the specimen is measured by recording the height of the pendulum at the end of the swing (see Figure c in next slide)

6. Charpy Impact TesterMotorized pendulum impact testing system a) Simplified illustration of the Charpy impact tester, (b-e) impact load and impact energy (lost to the specimen) characteristic of a steel specimen (f) acquired in ms time intervalsacbfdStarting positionEnd of swinghohfStrikerSpecimenAnvile

7. Simulated Vehicle CollisionsThe impact velocity is controlled by the initial height of the pendulum; the pendulum momentum at the onset of the collision is controlled by its mass and initial heightThe collision is a dynamic process, during which sliding occurs between the two surfaces resulting in a smear.The frictional force, responsible for the smear, depends on the normal force, which in turn depends on inertia (momentum) and the viscoelastic response of the colliding bodies

8. Charpy Impact TesterIn b and c, the reaction force is mainly created by the bending of the automotive specimen (elastic response) which we call the couponacbStrikerCouponAccessory IBefore CollisionPaint smearAccessory IAfter CollisionStrikerPaint smearPaint-transfer sample

9. Simulated Vehicle CollisionsHere energy is dissipated to friction as well as deformation of the coupon.The initial contact angle between the coupon and the striker is adjusted by mounting the coupon on the accessory using wedge washers.During the collision, the contact angle continuously changes with sliding and bending of the coupon.The accessory design emulates the sheet metal deformation in a real automotive collision.

10. IR MicroscopyA paint smear was obtained in which all layers were resolved. As revealed by an ATR-IR microscope, there was separation of the automotive paint layers in some regions.In contrast, the paint smear appeared intact everywhere using transmission IR microscopy. The unmixing was evident only with ATR-IR microscopy because of its superior spatial resolution.

11. IR Microscopy The transferred paint smear was separated from the inert metal substrate using a sharp knife.An IR image map was obtained from the smear using the imaging ATR accessory of the iN10MX IR microscope.Spectral line maps generated from this IR image map were decatenated to the pure spectrum of each layer using multivariate curve resolution (alternating least squares algorithm).

12. ALS ConditionsThe full IR spectrum of the paint samples, 4000 to 860cm-1, were used as input to ALS.Non-negativity and unimodality were both applied as constraints for the ALS algorithm.Initial estimates of the profiles for each constituent were provided by the Varimax Extended Rotation (see Barry K. Lavine, Jason P. Ritter, and Edward Voigtman, “Multivariate Curve Resolution in Liquid Chromatography – Resolving Two Way Multicomponent Data Using a Varimax Extended Rotation,” Microchemical Journal 2002, 72(2), 163-178)

13. Varimax Extended Rotation

14. Decatenated IR Spectrum of Clear Coat (red) Compared to IR Spectrum of Clear Coat from Original Sample (black)

15. Decatenated IR Spectrum of Surfacer (red) Compared to IR Spectrum of Surfacer from Original Sample (black)

16. Decatenated IR Spectrum of E-Coat (red) Compared to IR Spectrum of E-Coat of Original Sample (black)

17. Spectral Library SearchingLibrary searching of the decatenated spectra was performed using an ATR simulated library of the clear coat (OT2), surfacer (OU2) and e-coat (OU1) layers.These ATR simulated spectral libraries were calculated from IR transmission spectra of GM paint samples (2000-2006 production years) in residence in the PDQ database.An ATR simulation algorithm was used to convert the transmission IR spectra from PDQ into ATR spectra.

18. OMNIC SearchOMNIC was configured using correlation for search type and Happ-Genzel for the apodization function as this set of conditions generally yielded the best results when searching automotive top coat and undercoat layersThe ATR spectra were ranked for best match using the hit quality index to assess similarity between the ATR spectrum reconstructed for each layer using MCR and each library entry for a particular layer.

19. OMNIC SearchThe top five hits identified by the hit quality index for each layer were compared to the model and line of the vehicle from which the paint sample was obtained.The reconstructed ATR spectrum was judged to be correctly matched if the correct line and model were found in the hit list (top five hits) for that layer

20. Library Search ResultsAll reconstructed ATR spectra were correctly identified by OMNIC and were typically second matches.OT2OU1OU2HitHQIHitHQIHitHQI4th match97.932nd Match96.582nd Match95.77

21. ConclusionsTransfer of automotive paint resulting in a smear is caused by sheer stress created by friction.In the absence of heat generation, the paint is brittle and paint transfer will occur in the form of chips.The question as to the specific conditions of the collision that lead to a paint chip being transferred during a hit run versus a clear coat smear or a paint smear involving the mixing of multiple layers of paint can be answered using this approach

22. AcknowledgementsMark Sandercock, Royal Canadian Mounted Police Forensic Laboratory, 15707-118th Avenue, Edmonton, Alberta T5V 1B7Koichi Nishikida, Materials Science Center, College of Engineering, University of Wisconsin, Madison, WI 53706National Institute of Justice 2017-IJ-CX-0022. The opinions, findings, and conclusions or recommendations expressed in this publication / program / exhibition are those of the author(s) and do not necessarily reflect those of the Department of Justice.