Gears Gears A gear is a wheel with teeth that mesh together with other gears - PowerPoint Presentation

1. Gears

2. GearsA gear is a wheel with teeth that mesh together with other gears

3. GearsA gear is a simple machine like a leverThe larger the diameter of the gear the longer the lever

4. What are Gears used for?Ensure positive motionReverse the direction of rotationIncrease or decrease the speed of rotationChange the torqueChange the direction of a power sourceMove rotational motion to a different axisKeep the rotation of two axes synchronized

5. TermsPinion: smaller of a pair of gearsExternal Gear: teeth formed on the outer surface of a cylinderInternal Gear: teeth formed on the inner surface of a cylinder

6. Spur GearMost commonUsed to transmit power from one shaft to another parallel shaftMove opposite each other Driver gear is the gear connected to the motor

7. Spur GearAdvantages:Low manufacturing costSimple designEase of maintenanceDisadvantage:Less load capacityHigher noise level

8. Bevel GearUsed when two axes intersect at right anglesChanges the direction of driveSpiral BevelUsed: differential drives, hand drillsDisadvantage:Gears are designed to work specifically with each other not interchangeableMust be Precisely mounted

9. Rack and Pinion Geara toothed bar or rod that can be thought of as a sector gear with an infinitely large radius of curvature. Torque can be converted to linear force by meshing a rack with a pinion: the pinion turns; the rack moves in a straight line. Such a mechanism is used in automobiles to convert the rotation of the steering wheel into the left-to-right motion of the tie rod(s). Pinion is the round gearRack is the flat straight piece

10. Helical GearThe leading edges of the teeth are not parallel to the axis of rotation, but are set at an angle. Since the gear is curved, this angling causes the tooth shape to be a segment of a helix. Helical gears can be meshed in parallel or crossed orientationsThe angled teeth engage more gradually than do spur gear teeth, causing them to run more smoothly and quietly.Parallel configurationCross configuration

11. Worm GearWorm gears: resemble screws. A worm gear is usually meshed with a spur gear or a helical gear, which is called the gear, wheel, or worm wheel.Worm-and-gear sets are a simple and compact way to achieve a high torque, low speed gear ratio. Axles are perpendicular like bevel gears.

12. MaterialNonferrous alloysCast IronsPower metalPlastics - is commonly used where cost or weight is a concern. A properly designed plastic gear can replace steel in many cases because it has many desirable properties. including dirt tolerance, low speed meshing, the ability to "skip" quite well and the ability to be made with materials not needing additional lubrication. Manufacturers have employed plastic gears to reduce costs in consumer items including copy machines, optical storage devices, cheap dynamos, consumer audio equipment, servo motors, and printers.Steels are most commonly used because of their high strength-to-weight ratio and low cost.

13. Manufacturing How Gears are MadeMost of all gearing produced worldwide is produced by net shape molding. Molded gearing is usually either powder metallurgy or plastic moldingMany gears are done when they leave the mold (including injection molded plastic and die cast metal gears), powdered metal gears require sintering sand castings or investment castings require gear cutting or other machining to finish them. The most common form of gear cutting is hobbling, but gear shaping, milling, and broaching also exist. 3D printing as a production method is expanding rapidly. For metal gears in the transmissions of cars and trucks, the teeth are heat treated to make them hard and more wear resistant while leaving the core soft and tough. For large gears that are prone to warp, a quench press is used.

14. Gear StandardsAmerican Gear Manufacturers Association - AGMAorganized in 1916 to formulate quality standards for gear inspection to reduce noise from automotive timing gearsin 1993 AGMA assumed leadership of the ISO committee governing international standards for gearing.

15. Sprocket Two gears that don’t touchDriven by a chain Both sprockets turn the same direction

16. Sprocket Examples:Bikes, machinery, motorcycles,Tracked vehicles, film projectors

17. Every day Uses of GearsHand can opener, non digital watch/clock, bike, egg beater, sprocket: movie projector-used in film transport mechanisms, car transmission, drill.

18. RatiosA ratio is a statement of how two numbers compare. Ratios can be written as a:b a to b or We write ratios the same way regardless of what we are describing. We have already been using ratios when we describe the scale of views on drawings.  

19. Ratios on drawings - scale down1:1 or full size means: one inch measured on the drawing = one inch on the real part1:2 or one to two - for every one inch measured on the drawing = two inches on the real part-This means to scale down the part is smaller on the drawing than in real life1:4 or one to four - for every one inch measured on the drawing = four inches on the real part –This means to scale down the part is smaller on the drawing than in real life

20. Ratios on drawings - scale upWe can also scale things to be larger than real size2:1 or two to one - for every two inches on the drawing = one inch on the real part – scale up the part looks bigger on the drawing than in real life4:1 or four to one – for every four inches on the drawing = one inch on the real part – Scale up the part – the part looks bigger on drawing than in real life.

21. Ratio How to write themCan be written as a:b, a to b, or . We will use a:b formatFor example lets compare 15 dogs to 10 cats Cats to dogs 10:15 Dogs to Cats 15:10 The order matters

22. Ratio How to write themWe can also reduce ratios similar to fractions10:15 to 2:3 or 15:10 to 3:2We can also compare the total to the partsDogs 15, cats 10, total 25Cats to Total 10:25 or 2:5Dogs to Total 15:25 or 3:5

23. Gear Teeth AdvantagesThey prevent slippage between the gears - therefore axles connected by gears are always synchronized exactly with one another.They make it possible to determine exact gear ratios - you just count the number of teeth in the two gears and divide. So if one gear has 60 teeth and another has 20, the gear ratio when these two gears are connected together is 3:1.They make it so that slight imperfections in the actual diameter and circumference of two gears don't matter. The gear ratio is controlled by the number of teeth even if the diameters are a bit off.

24. 2 Gears equal teeth Gears with equal amount of teeth the ratio is 1:1 ClockwiseCounter Clockwise

25. Unequal Gear Size Gears with unequal teeth the ratio is one to anotherFor example: 1:2 1:3 1:4 or 2:1 3:1 4:1For each complete revolution of the large gear The small gear will revolve more than once depending on the ratioClockwiseCounter ClockwisePinion Gear orDriver – input gearConnected to the motorDriven-output gearConnected to the wheel

26. Gear RatiosFor example: 1:2 Gear A 20 teeth Gear B 10 teeth 1:4 Gear A 20 teeth Gear B 5 teeth 2:1 Gear A 10 teeth Gear B 20 teeth3:1 Gear A 25 teeth Gear B 75 teeth4:1 Gear A 20 teeth Gear B 80 teethFor each complete revolution of the large gear The small gear will revolve more than once depending on the ratioExample 1:2 the large gear turns once the small one twiceCounter ClockwisePinion GearDriverClockwiseDriven

27. A basic rule of gearsWhen transmit power from a motor to a wheel:The gear connected to motor is driver or input gearThe gear connected to the wheel is the driven or output gear (ratio is the number of teeth on each gear)Gear Ratio GR is : output:input or driven:driverCan rewrite as a fraction: GR = output/input = driven/driver

28. Basic rules of gearsIf a gear gives more force get less speedIf get more speed get less forceSmall gears driving large gear: torque increasesLarge gear driving small gear: torque decreasesSmall gear driving big gear: speed decreasesLarge gear driving small gear: speed increases

29. A basic rule of gearsWhen a large gear turns a small gear the speed increases, this is gearing up. small gear turns a large gear the speed decreases, this is gearing down.

30. Torquemoment of force is the tendency of a force to rotate an object about its axis or pivot mathematically: torque is defined as the cross product of the lever-arm distance vector and the force vector, which tends to produce rotation.

31. You are designing an arm with a reach of 0.4m lifting a 10N object. The load on the motor can’t be any more than 0.803 N-m What gear reduction is required?torque = Force x Distance (force = 10 N distance = 0.4m ) Torque = 10N x 0.4 m = 4 N-m (output torque)Output torque = input torque x gear reduction (solve for gear reduction)Gear reduction = output torque/input torque (input torque=motor= 0.803 N-m)Gear reduction = 4 N-m/0.803 N-mGear reduction = 4.981Given the following gears: 12-tooth, 36-tooth, 60-tooth, and 84-tooth what combination with work?Example Problem

32. Given the following gears: 12-tooth, 36-tooth, 60-tooth, and 84-tooth what combination with work? (Want 4.981 answer from other slide)These are the available gear ratios:So two gears 60:12 will give a reduction of 5 which is closest to 4.981Divide first number by the second number

33. The End