1 2 Catalogue 1 I nstruction 3 2 Breakout board view ID: 822124
Download Pdf The PPT/PDF document "Breakout board V5 user manual" is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.
1 Breakout board V5 user manual
1 Breakout board V5 user manual 2 Catalogue 1、Instruction： ............................................................................................................................... 3 2、B
reakout board view： ...............
reakout board view： ............................................................................................................... 3 3、The connection between breakout board and driver： ............. Error! Bookmark not defined. 4、Limit s
witch connection： .................
witch connection： .......................................................................................................... 4 5、DB25 parallel port definition： ................................................ Error! Bookmark not defined. 6
、Mach3 software setting： .....
、Mach3 software setting： ......................................................... Error! Bookmark not defined. 6.1、MACH open： ............................................................... Error! Bookmark not defined. 6.2、driver
MACH3 setting：....................
MACH3 setting：................................................ Error! Bookmark not defined. 6.3、limit switch MACH3 setting： ...................................... Error! Bookmark not defined. 6.4、The G code run： ....................
.......................................
....................................... Error! Bookmark not defined. 3 1、Instruction: It can most connection 5pcs driver and control 5pcs motor in the same time It is w
ith 4-wire limit switch to insure our
ith 4-wire limit switch to insure our safty movement It is with relay port to contro the cnc spindle Working voltage is 5VDC and support with MACH3,EMC2,KCAM4 software 2、Breakout board view: 4 3、The connection between breakout
board and driver： 4、Limit s
board and driver： 4、Limit switch port connection： 5 5、DB25 parallel port definition Fig 5.1 Parallel port output PIN definition： PIN1 PIN2 PIN3 PIN4 PIN5 PIN6 PIN7 PIN8 PIN9 PIN10 STEPE STEPA DIRA S
TEPB DIRB STEPC DIRC STEPD DIR
TEPB DIRB STEPC DIRC STEPD DIRD DIN1 B axis PU X axis PU X axis DIR Y axis PU Y axis DIR Z axis PU Z axis DIR A axis PU A axis DIR Limit 1 PIN11 PIN12 PIN13 PIN14 PIN17 PIN16 PIN18~25 DIN2 DIN3 DIN4 D
IRE EN RLY GND Limit 2 L
IRE EN RLY GND Limit 2 Limit 3 Limit 4 B axis DIR All axis enable Relay GND 6 6、Mach3 software setting： 6.1MACH open： Fig 1 Open MACH3 software，select mach3MILL then click OK 7 Fig 2
MACH3 interface 6.2、Driver MACH3
MACH3 interface 6.2、Driver MACH3 setting： See Fig 3，Open the PORT &PINS menu of config menu 8 Fig 3 Fig 4 9 Set up the circle 1 of Fig4 for the frequency which influence the stepper motor speed,then set u
p the circle 2 as below Fig 5 for PIN
p the circle 2 as below Fig 5 for PIN Fig 5 Pls setting the software as above according to our definition of breakout PIN 10 Fig 6 The select “output signals” as Fig 6, set up the pin numer as 16 and 17. 6.3、Limit switch MACH
3 setting： Click “input signal
3 setting： Click “input signal” to setting as below Fig 7 11 Fig 7 6.4、Run of the G code： See Fig 8,open the G code menu 12 Fig 8 Find your G code,then open as Fig 9: Fig 9 13 Fig 10 You will see
“RESET” flicker after open th
“RESET” flicker after open the G code,you can click it to stop flicker,then run the circle2 “CYCLESTART” in addition if you need manual control,you can press the TAB of keyboard,the manual control interface as below Fig 11 14 Fi