ZICO1054PM1LOAD LOCK153 WALKAWARTSREV 62718 SCBA bracket is composed of a Requires assembly in the x00660069eld All hardware for with a Torx head screwdriver and 716 wrench The KDULLHKnockdown ID: 859458
Download Pdf The PPT/PDF document "Where SCBA units are mounted within SCBA..." is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.
1 ZICO®1054PM1 "LOAD & LOCK"™ WALKA
ZICO®1054PM1 "LOAD & LOCK"™ WALKAWA ® RTS REV. 6-27-18 "Where SCBA units are mounted within SCBA device in its stowed position shall be such that the SCBA unit cannot The NFPA Standard requires the holding device to "retain the SCBA unit whensubjected to a 9G force". Additionally, the SCBA bracket is composed of a Requires assembly in the �eld. All hardware for with a Torx head screwdriver and 7/16" wrench. The KD-ULLHKnockdown BracketKD-ULLHKnockdown Bracket(Shown w
2 ithout LLS strap)2.Assembled bracket (mo
ithout LLS strap)2.Assembled bracket (model ULLH):Bracket is assembled at our factory for immediate All bracket components are material. This durable, crack/peel-resistant coating to the air cylinder, and has been tested to over 50,000 What footplate styles are available? The Model cylinders. An optional Model NEF footplate is What style strap is required? NFPA 1901-04, restraining the SCBA when mounted in the crew area What if the SCBA unit stays in the bracket A Model LLES Ejector
3 Spring with the NFPA Standard. Page 3 PA
Spring with the NFPA Standard. Page 3 PART NO.QTY.Cambuckle/Tab AssemblyAdjustment Strap Assembly1" Tri-Glide9010-162511MODEL LLS "LOAD & LOCK" STRAPMODEL KD-ULLH OR ULLH BRACKET On seats that are excessively tilted back, an Ejector Spring Specify model LLES Ejector SCBA units.(component items are shown on page 3)Lay universal backplate (13) along side of SCBA Short footplate may need to be invertedValve assembly should be placed next toassembly.Adjust SCBA cylinder so that cylinder w
4 illcontact with the cylinder. RTS & A St
illcontact with the cylinder. RTS & A Start nuts (11) onto screws.Tighten with 7/16" wrench and Torx headscrew driver.into contact with air cylinder. between base of seat and the air cylinder.backplate at positions A & E (see above).To mount completed "Load & Lock" bracket to Page 5 NVERT Remove bolts (1) and lock nuts (11) retaining theRemove bolts (10) and lock nuts (11) holding the(10) and lock nuts (11) provided.bracket is longer, remove the long extension and You are now ready to adjus
5 t the "Load & Lock" " WALKAWA Tilt cyli
t the "Load & Lock" " WALKAWA Tilt cylinder back until it is touching both seatsWith the other hand, bring the strap around thecylinder.to a full and complete stop at the emergency scene The LLS strap will pass between the SCBA unitand the �re�ghter. Page 6 APPA Mounting in crew area:When mounting SCBA brackets in theStrap must be used with the bracket. The the SCBA and bracket. If the bracket is times the weight of the SCBA and bracket.Mounting hardware:the bracket
6 . The center hole, at each seat locatio
. The center hole, at each seat location, is made for a 5/16" screw. We location 1, 2 or 3. The bottom screw should be at seat locations 4 or 5. All member. Nut and washer should be on the back side of the supporting member. Forward or rear facing seats:When mounted in specially designed SCBA seats, the bracket and LLS either side of the bracket. The angle between the back of the bracket and NOTE: When the SCBA is placed into the should fall out. If it does not, you will need to ins
7 tall model LLES Ejector Spring (page 3)
tall model LLES Ejector Spring (page 3) to be in compliance with NFPA 1901-04. Side facing seats:When the bracket and LLS are mounted so that the passenger's side faces towards the front or rear of the Page 7 APPA Mounting outside the crew area:When SCBA is mounted outside of the crew area, it & Lock" bracket is not required. However, we Figure 1.Figure 2. When the bracket is mounted vertically, should be placed against the air cylinder. An NSF next to the cylinder. MOD LLJEO P PART NO.
8 QTY.1045-275-1139010-162511 10 West Coll
QTY.1045-275-1139010-162511 10 West College Avenue, P.O. Box 337, Yardley, PA 19067-0587(215) 493-3618FAX: (215) 493-1401*ZICO is a registered trademark for �re, safety and marine products made by Ziamatic Corpwww.ziamatic.comTOLL FREE: 800-711-3473 A See page 3 for parts list and page 4 for hole locations.will not damage SCBA components.surface of SCBA backplate.If you have additional questions or are uncertain about mounting your ZICObracket, call 1-800-711-3473 for assistance