By, Prof. R.S. Chaudhari. - PowerPoint Presentation

1. By, Prof. R.S. Chaudhari.Asst. professor Mechanical Engineering DepartmentMCQ for Unit 1

2. Question 1The uniform wear conditions are used …….. a) for maximum power to be transmitted b) for safe design of clutches c) for safe design of bearings d) for overcoming the frictional torque.

3. Question 2The uniform pressure conditions are used ……. a) for maximum power to be transmitted b) for safe design of clutches c) for safe design of bearings d) for overcoming the frictional torque.

4. Question 3For safe design of bearing, we assume …….. a) maximum power to be transmitted b) safe design of clutches c) safe design of bearings d) overcoming the frictional torque.

5. Question 4For safe design of clutches, we assume …….. a) uniform pressure conditions b) uniform wear conditions c) Neither uniform pressure nor uniform wear d) All of the above.

6. Question 5According to uniform wear theory ……. a) P·ω = constant b) P· r = constant c) P·W = constant d) P·T = constant

7. Question 6In case of foot step bearing, the frictional force under the conditions of uniform wear may be assumed to be acting at ……. a)r b) ½ r c) 3/2 r d) 2/3 r

8. Question 7The ratio of friction torque for uniform pressure to uniform wear for the same dimensions and load is …….a) > 1 b) =1 c) < 1 d) = ½

9. Question 8Torque required to overcome the friction between shaft and bearing surface in case of multiple flat collar bearing is ……..a)Independent of no of collars b)dependent on radius of collar C)dependent of no of collars D)Non of above .

10. Question 9According to uniform wear theory frictional torque transmitted by conical pivot bearing is …… a) 2/3 μ W R cosec α b) 1/2 μ W R cosec α c) 1/2 μ W R cos α d) μ W R cosec α

11. Question 10Frictional torque as per uniform wear theory is …………. (a)µP(R0+Ri) (b)½ µP(R0+Ri) (c) ½ µP

12. Question 11In case of flat pivot bearing, the rubbing velocity is……… (a)maximum at the centre of the contact area (b)zero at the centre & maximum at the outer radius (c)uniform throughout the contact area (d) zero at the outer radius

13. Question 12The rate of wearing in case of flat pivot bearing is…… (a)inversely proportional to the pressure intensity (b)directly proportional to the rubbing velocity (c) directly proportional to the pressure intensity (d)both (b) &(c)

14. Question 13For calculating the friction power of bearing, the assumptions made in practise are…… (a)the rate of wearing at the surface is uniform (b) the rubbing velocity is constant (c) the pressure intensity is uniform (d) (a) & (c) only

15. Question 14In case of flat pivot bearing, the frictional torque transmitted for uniform pressure as compared to the frictional torque transmitted for uniform wear…… (a)is more (b)is less (c)is constant (d)may be more or less

16. Question 15The frictional torque, transmitted in case of flat pivot bearing for uniform pressure, is equal to……… (a)µWR (b) µWR (c) µWR (d) µWR

17. Question 16In case of flat pivot bearing, the frictional torque transmitted for uniform pressure as compared to the frictional torque transmitted for uniform wear Is equal to….. (a)µWR (b) µWR (c) µWR (d) µWR

18. Question 17The ratio of frictional torque for uniform pressure to the frictional torque transmitted for uniform wear in case of flat pivot, is equal to……. (a) 1/3 (b) (c)1.0 (d)

19. Question 18The frictional torque, transmitted in case of a flat collar bearing for uniform pressure ,is equal to……… (a)µW (b) (c)(R1+R2) (d)(R1-R2)

20. Question 19The frictional torque for the same diameter in a conical bearing is _____ than in a flat bearing. (a) more (b) less (c)equal (d)may be more or less

21. Question 20The frictional torque transmitted by a conical collar bearing is _______. (a)less than that of flat collar bearing (b)equal than that of flat collar bearing (c)more than that of flat collar bearing (d)none of the above

22. Question 21The frictional torque produced due to friction for same shaft diameter, in conical bearing is ___.(a)less than that for flat bearing (b)equal to that for flat bearing(c)more than that for flat bearing (d) may be more or less depending upon cone angle

23. Question 22Choose the wrong statement. (a)The frictional torque transmitted by a shaft fitted with a large number of collers is the same as transmitted by a shaft with one coller. (b)The frictional force for uniform pressure , in case of a flat pivot bearing, can be assumed to be acting at distance of 2/3 of the radius of the shaft from the axis of shaft. (c)when horse power lost in friction is to be determined, uniform pressure is assumed for safe design of bearing (d) The frictional force for uniform pressured, in case of a flat coller bearing, can be assumed to be acting at distance of 1/2 of the sum of internal and external radii of the shaft.

24. Question 23The frictional torque transmitted in a conical pivot bearing , concider uniform wear , is ____. (a)1/2 × µ×W×R ×cosecα (b) 3/2 × µ×W×R ×cosecα (c) 3/4 × µ×W×R ×cosecα (d) µ×W×R ×cosecα

25. Question 24For pivot bearing with r₁ & r₂ as the outer and inner radii & W as the axial load, the frictional torque , assuming uniform pressure is given by ______. (a) 1/2× µ×W (r₁ + r₂) (b) 1/2× µ×W (r₁ - r₂) (c) 2/3 ×µ×w( (r13-r23)/(r12 –r22)) (d) ) 2/3 ×

26. Question 25For coller bearing with r₂ & r₁ as inner and outer radii & W as axial load, assuming uniform wear, is given by ______. (a) 1/2× µ×W (r₁ + r₂) (b) 1/2× µ×W (r₁ - r₂) (c) 2/3 ×µ×w( (r13-r23)/(r12 –r22)) (d) ) 2/3 ×µ×w( (r13-r23)/(r12 +r22))

27. Question 26The ratio of frictional torque produced for uniform wear to that for uniform pressure is ________. (a)1 (b)2/3 (c)4/3 (d)3/4

28. Question 27In case of pivot bearing the rate of wear is ______. (a)maxm at the center of contact area (b) zero at the center of contact area (c)uniform throughout the contact area (d) zero at the maximum radius of the contact area

29. Question 28The number of collars are provided to carry a fixed axial force in a flat collar bearing _____. (a)to increase torque (b) to decrease torque (c) to decrease intensity of pressure (d) to increase intensity of pressure

30. Question 29In flat pivot bearing the total moment of friction force______ a)for uniform wear is greater than that for uniform pressureb) for uniform wear is less than that for uniform pressure c) for uniform wear is equal to that for uniform pressure d) for uniform wear may be more or less and connot be predicted

31. Question 30In flat pivot bearing the total power lost in friction ______ a) for uniform wear is greater than that for uniform pressure b) for uniform wear is less than that for uniform pressure c)for uniform wear is same as that for uniform pressure d) for uniform wear may be more or less pressure and connot be predicted

32. Question 31The frictional torque produced in case of flat pivot bearing for uniform wear and uniform pressure respectively is (W = total axial load,µ =co-efficient of friction,r =radius of pivot)a)1/2µ W r and 2/3 Wµ r b)2/3µ W r and 1/2µ W rc)1/3µ W r and 1/2µ W rd)1/2µ W r and 1/3µ W r

33. Question 32To be on the safe side in design ,the uniform pressure and uniform wear is Assumed respectively_________A)for power transmitted by friction and power lost due to friction b)For power lost due to friction and power transmitted by friction c)For torque transmitted by friction and friction torque overcome d)None of the above

34. Question 33choose the correct statement for safe design a) for power lost in friction uniform wear is assumedb) for power lost in friction uniform pressure is assumed c) for power transmitted due to friction uniform pressure is assumed d) for power transmitted due to friction or lost in friction uniform wear is assumed

35. Question 34choose the correct statement for safe designa) for power transmitted by friction uniform wear is assumed b) for powertransmitted friction uniform pressure is assumed c) for power lost in friction and power transmitted uniform wear is assumed d) for power lost in friction and power transmitted uniform pressure is assumed

36. Question 35The purpose of providing multiple collars on a flat collar pivot bearing is to a) Establish self sustaining bearing conditions b) Increase the frictional resistancec) Distribute the axial load because of limiting bearing pressures on the bearing d) Increase th e power absorbed by the bearing

37. Question 36Frictional torque produced for uniform pressure for conical pivot Bearing having semi angle of cone = α is equal to_____A)µ W r1/2 B)2 µ W r1/3 C)µ W r1/3 D)3 µ W r1/4

38. Question 37Frictional torque developed due to uniform wear for conical Bearing with semi cone angle = α is_____A)µ W r1/2 B)2 µ W r1/3 C)µ W r1/3 D)3 µ W r1/4

39. Question 38In a multi-collared thrust bearing consisting of ‘n’ collars and Subjected to axial load W,load sheared by each collar is_____A)WB)W/nC)W/(n-1)D)None of these

40. Question 39 Brakes are self-energizing when …………..A)Frictional torque assists the applied torque.B)Frictional torque opposes the applied torque.C)Frictional torque vanishes.D)None of above. 

41. Question 40In a differential band brake, as shown in fig.1 the length OA is greater than OB. In order to apply the brake, the force at C should …………..A)Be zero.B)Act in downward directionC)Act in upward directionD)None of the above

42. Question 41For the brake to be self locking, the force P at C as shown in figure 1 should……..A)Be zeroB)Act in downward directionC)Act in upward direction

43. Question 42When brakes are applied to all four wheels of a moving car, the distance travelled by the car before it is brought to rest, will be……..A)Maximum b) minimum C)Both a and b d) none of the above

44. Question 43Which of the following brakes is commonly used in two wheelers?A)Disc brakeB)Band brakeC)Internal expanding shoe brakeD)A and B

45. Question 44Brakes commonly used in trains are ……… brakesA)BandB)ShoeC)Band and blockD)Internal expanding shoe

46. Question 45In a self locking brake, the force required to apply the brake is………A)MinimumB)MaximumC)ZeroD)None of the above

47. Question 46When the frictional force helps the applied force in applying the brake, the brake is ………A)Self lockingB)AutomaticC)Self-energisingD)A and C

48. Question 47In an internal expanding shoe brake, more than 50% of the total braking torque is supplied by…..A)Leading shoeB)Trailing shoeC)Any of the twoD)None of these

49. Question 48which of the following is classified a absorption type of dynamometer ? a) prony brake dynamometer b) rope brake dynamometer c) hydraulic dynamometer d) all of above

50. Question 49which of the following is classified as transmission type of dynamometer a) prony brake dynamometer b) rope brake dynamometer c) hydraulic dynamometer d) epicyclic dynamometer

51. Question 50which of the following is an absorption type of dynamometer ?a) prony brake dynamometer b) rope brake dynamometer c) epicyclic-train dynamometer d) both (a) & (b)

52. Question 51in transmission type of dynamometers ,the available power is ………….a) absorbed in overcoming the frictional work . b) transmitted except that the small power is absorbed due to friction.c) fully transmitted .d) none of the above

53. Question 52an example of absorption type dynamometer is…………..a) prony brake dynamometerb) epicyclic-train dynamometerc) torsion dynamometer d) belt transmission dynamometer

54. Question 53 an example of transmission type dynamometer is…………..a)prony brake dynamometerb)rope brake dynamometerc) Froude dynamometerd) torsion dynamometer

55. Question 54which of the following is classified as absorption dynamometer ? a) prony brake dynamometer b) rope brake dynamometer c) Froude ’shydraulic dynamometerd) all of the above

56. Question 55 which of the following is classified as transmission dynamometer? a) torsion dynamometer b) Froude ’s hydraulic dynamometer c) belt dynamometer or tathamdyanamometer d) prony brake dynamometer

57. Question 56 cooling water is use in……………. a)prony brake dynamometer b)epicyclic gear train dynamometer c)torsion dynamometerd)rope brake dynamometer

58. Question 57tatham dynamometer is name given to ………………d)rope brake dynamometerb) belt transmission dynamometerc) absorption dynamometer d) epicyclic train dynamometer

59. Question 58incase of glibson flash light torsion dynamometer angle of twist can be measured upto………………..a) 1th /20 and degreeb) 1th /10 of degreec) 1th /70 of degreed) 1th /100 of degree

60. Question 59in case of dynamometer function of counter weight is toa)balance the brake when unloadedb)adjust pressure on pulley to control speed .c)prevent rotation of block due to friction between block and pulleyd) to clamp the block

61. Question 60F the force at lever end acts as downwards then condition for self-locking is (a) b/a<e^u for counter-clockwise direction (b) b/a<e^u fo clockwise direction (c) b/a<e^u for both direction (d) none of above

62. Thanks

63.

64.

65. Unit 3 AnswersQue. NoAnsQue. NoAnsQue. NoAnsQue. NoAnsQue. NoAnsQue. NoAns1B11B21C31A41A51B2C12D22D32B42C52A3A13D23A33B43D53D4B14A24C34A44B54D5B15B25A35C45C55C6B16D26D36D46C56D7A17D27B37A47A57B8A18B28C38B48D58D9B19A29B39B49D59A10B20C30B40B50D60B