MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO - PDF document

MARTIN ENGINEERING HEREBY DISCLAIMS ANY LIABILITY FOR: DAMAGE DUE TO CONTAMINATION OF THE MATERIAL; USER’S FAILURE TO INSPECT, MAINTAIN AND TAKE REASONABLE CARE OF THE EQUIPMENT; INJURIES OR DAMAGE RESULTING FROM USE OR APPLICATION OF THIS PRODUCT CONTRARY TO INSTRUCTIONS AND SPECIFICATIONS CONTAINED HEREIN. MARTIN ENGINEERING’S LIABILITY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF EQUIPMENT SHOWN TO BE DEFECTIVE.Observe all safety rules given herein along with owner and Government standards and regulations. Know and understand lockout/tagout procedures as defined by American National Standards Institute (ANSI) z244.1-1982, American National Standard for Personnel Protection - Lockout/Tagout of Energy Sources - Minimum Safety Requirementsth Administration (OSHA) Federal Register, Part IV, 29 CFR Part 1910, Control of Hazardous Energy Source (Lockout/Tagout); Final RuleThe following symbols may be used in this manual: DANGER : Immediate hazards that will result in severe personal injury or death. WARNING Warning: Hazards or unsafe practices that could result in personal injury. CAUTION Hazards or unsafe practices that could result in product or property damages. IMPORTANTImportant: Instructions that must be followed to ensure proper inst NOTE General statements to assist the reader. Martin Engineering M3493-08/13MartinImpact Cradles LD and MD SectionPageList of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iiList of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iiIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Impact Cradle Materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Materials Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Before Installing Impact Cradles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Installing Impact Cradles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Measuring Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Installing Impact Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4After Installing Impact Cradle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Troubleshooting/Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Part Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Martin Engineering M3493-08/13MartinImpact Cradles LD and MD FigureTitlePage1Measuring for Martin Impact Cradles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Installing Martin Impact Cradles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Martin Impact Cradle LD Assembly, P/N 36010-XXX . . . . . . . . . . . . . . . . . . . . . . . . . . 144Martin Impact Cradle MD Assembly, P/N 36318-XXX . . . . . . . . . . . . . . . . . . . . . . . . . 175Martin Impact Cradle MD Assembly with 5 ft. bars, P/N 36516-XXX . . . . . . . . . . . . . 216Conveyor Products Warning Label, P/N 23395 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 TableTitlePageIMartin Impact Cradle Materials and Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . .1IIPart Numbers an Impact Cradle LD. . . . . . . . . . . . . . . . . . . . . . . .16IIIPart Numbers an Impact Cradle MD . . . . . . . . . . . . . . . . . . . . . . .19IVPart Numbers an Impact Cradle MD with 5 ft. bars. . . . . . . . . . . .23 Martin Engineering M3493-08/13MartinImpact Cradles LD and MD Impact Cradles LD and MD are layered, shock-absorbing conveyor belt transfer point products engineered for use in bulk solids handling industries.ReferencesThe following documents are reAmerican National Standards National Standard for Personnel Protection - Lockout/Tagout of Energy Sources - Minimum Safety Requirements, American National Standards Institute, Inc., 1430 Broadway, New York, NY 10018.Federal Register, Volume 54, Number 169, Part IV, 29 CFR Part 1910, Control of Hazardous Energy Source (Lockout/Tagout); Final RuleDepartment of Labor, Occupational Safety and Health Administration (OSHA), 32nd Floor, Room 3244, 230 South Dearborn Street, Chicago, IL 60604.Materials and specifications for the Martin Impact Cradles are shown in Table I.Table I. Martin Impact Cradles Materials and SpecificationsSafetyAll safety rules defined in the above documents and all owner/employer safety rules must be strictly followed when working on this equipment.Only standard hand tools are required to install and service this equipment.CharacteristicsBar With UHMW TopMSHA-Accepted for Underground UseCoefficient of Friction0.5Service Temperature-20 to 140°F (-29 to 60°C) BarConstructionBearing LayerUHMW PolyethyleneAbsorption Layer83A-Durometer UrethaneT-SlotAluminumFasteners0.5-in. dia. Bolts Introduction Martin Engineering M3493-08/13MartinImpact Cradles LD and MD 1.Inspect shipping container for damage. Report damage to delivery service immediately and fill out delivery service’s claim form. Keep any damaged goods subject to examination.2.Remove Martin Impact Cradle from shipping container. Equipment in container should include the following:Martin Impact Cradle LD or MD AssemblyTwo Conveyor Products Warning Labels, P/N 233953.If anything is missing or damaged, contact Martin Engineering or a representative.4.Make sure belt is centered on conveyor. WARNING Before installing equipment, turn off and lock out/tag out energy source to conveyor and conveyor accessories.5.Turn off and lock out/tag out energy source according to ANSI standards (see “References”). WARNING If equipment will be installed in an enclosed area, gas level or dust content must be tested before using a cutting torch or welding. Using a cutting torch or welding in an area with gas or dust may cause an explosion.6.If using a cutting torch or welding, test atmosphere for gas level or dust content. Cover conveyor belt with fire retardant cover.7.If not already present, install an impact idler 1 in. (25 mm) ahead of and 1 in. (25 mm) behind Martin8.Remove any unnecessary idlers. (The Martin Impact Cradle can replace up to four impact idlers.) Martin Engineering M3493-08/13MartinImpact Cradles LD and MD Figure 1. Measuring for Martin1.See Figure 1. Make sure chute walls and/or wear liners are correct distance above belt as shown. If necessary, modify chute walls and/or wear liners.2.Mark center of loading point on stringer; both sides of belt.3.Install an idler 1 in. (25 mm) beImpact Cradle.4.Measure and align either first cross-support beam or second cross-support beam from tail pulley with center of loading point. 1 (25).375 (9) Center 1 (25).75 (19)Belt TravelTapered endof bar Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD1.Slide cross-supports under belt in pre-determined location and align with 2.Make sure base weldment cross-supports are perpendicular to belt, or bars will wear unevenly and maintenance will be difficult. Make sure center bars are centered below belt and are parallel to belt travel.3.Make sure distance from top of center bar to bottom surface of belt measures 1/2 in. (12 mm) maximum for troughed belts and 1/4 in. (6mm) for flat belts (see Figure 2). If distance is greater than this, add shims under base weldment to raise impact cradle to height of adjacent idlers. (Shim Kit, P/N 34163 is available from Martin Engineering.) If distance is less than this, contact Martin Engineering or a representative.4.For troughed belts, make sure clearance between belt and wing section is 1/2 in. (13 mm) where wing section meets base and tapers to no clearance between belt and wing section at outside edge (as shown in Figure 2). NOTE Martin Engineering recommends bolting rather than welding for easier accessibility and 5.Bolt or weld base weldment to stringers as follows:a.If bolting, drill or cut 9/16-in. holes in stringers through mounting holes in feet of base weldment cross-supports. Install hex head cap screw, flat washer, compression washer, and hex nut (Figure 2) in each hole to secure base weldment to stringers.b.If welding, clean stringer of rust and dirt. Then stitch weld I-beams to 6.If removed for installation, install impact bars and/or wing section(s). Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MDFigure 2. Installing Martin7.Measure the distance from the idler to the first cross member bolt. Verify the dimensions and tighten the bolt into place. (Refer to Figure 3 for Impact Cradle LD dimensions and Figure 4 for Martin Impact Cradle MD dimensions.) .50*(13) A. Impact Bar w/ Aluminum TrackC. Wing Support PlateD. Hex Head Cap Screw Flat WasherHex Nut E. Left Wing AngleCompression Washer* .25 in. (6 mm) for flat belts Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD8.Measure between cross support channels. Make sure the cross-support is 9.Tighten bolts.10.Repeat for remaining cross support channels.11.Install impact bars. Tapered ends of bars must be located as shown.12.Line bolts up with slots and repeatss sections. Tighten 13.Repeat for additional center bars. Belt Travel Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD14.Bolt wings in the correct holes but do not tighten.15.Bolt on the fine tune adjustment angle but do not tighten.16.Bolt on the eccentric angle adjuster but do not tighten. NOTE Proper hole selection is important in obtaining the desired troughing angle (e.g., 20°, 35°, 45°).17.Install impact bars on wings. Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD18.Rotate fine adjustment cam until wing bars are touching belt.19.Tighten bolts.20.Repeat steps 9–19 for opposite side. Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD After Installing Impact Cradle IMPORTANT Read entire section before beginning work.1.Thoroughly wipe outside chute walls clean above Martin Impact Cradle on both sides of chute. Place a Conveyor Products Warning Label (P/N 23395) on each chute wall visible to belt operator. WARNING Failure to remove tools from installation area and conveyor belt before turning on energy source can cause serious injury to personnel and damage to belt.2.Remove all tools and fire retardant cover from installation area and conveyor belt. DANGER Do not touch or go near conveyor belt or conveyor accessories when conveyor belt is running. Body or clothing can get caught and pull body into conveyor belt, causing severe injury or death.3.Turn on conveyor belt. WARNING Before adjusting impact cradle, turn off and lock out/tag out energy source to conveyor belt and conveyor accessories.4.After 1 hour of operation, turn off and lock out/tag out energy source according to ANSI standards (see “References”).5.Make sure all fasteners are tight. Tighten if necessary.6.Inspect impact bars for wear. (A small amount of “break-in” wear may be found. This will stop once the bars wear to conveyor belt contour.)7.If excessive wear, uneven wear, or some other problem exists, see “Troubleshooting/ Installation Checklist.” After Installation Martin Engineering M3493-08/13MartinImpact Cradles LD and MD Maintenance IMPORTANT Read entire section before beginning work. WARNING Before servicing impact cradle, turn off and lock out/tag out energy source to conveyor belt and conveyor accessories.1.Turn off and lock out/tag out energy source according to ANSI standards (see “References”).2.Make sure all fasteners are tight. Tighten if necessary.3.Check bars for wear. If light-colored top covering on bars is worn through to orange urethane, replace bars as follows:a.If center bars are worn:(1)Remove wing assemblies with bars by removing bolts and set aside for reinstallation.(2)Loosen bolts on impact bars up to and including the worn bars.(3)Remove impact bar and bar holder.(4)Replace worn bars on bar holders and reinstall in reverse order.b.If wing bars are worn:(1)Loosen wing assemblies with bars by removing bolts and slide towards the side of the belt.(2)Loosen bolts on worn impact bars.(3)Remove impact bar and bar holder.(4)Replace worn bars on bar holders and reinstall in reverse order.4.Remove fines between impact bars with broom or high-pressure air or water.5.Inspect impact cradle for cracks or fatigue. Weld or strengthen structure as necessary.6.Wipe warning labels clean. If labels are not readable, contact Martin Engineering or a representative for replacements. WARNING Failure to remove tools from maintenance area and conveyor belt before turning on energy source can cause serious injury to personnel and damage to belt.7.Remove all tools from maintenance area. DANGER Do not touch or go near conveyor belt or conveyor accessories when conveyor belt is running. Body or clothing can get caught and pull body into conveyor belt, causing severe injury or death.8.Start conveyor belt. Maintenance Martin Engineering M3493-08/13MartinImpact Cradles LD and MD TroubleshootingIf you are experiencing problems with Martin Impact Cradle, see below:checklistIf after taking corrective actions suggested under “Troubleshooting” you are still experiencing problems, check for the following:SymptomCorrective ActionHigh impact bar wear rate.Impact cradle is installed too close to belt. Make sure impact cradle surface is 1/2 in. (13 mm) below troughed belt and 1/4 in. (6 mm) below flat belt.Impact bars worn unevenly.Belt is unevenly loaded, wear liners are improperly installed, and/or impact bars are not parallel to belt travel. Inspect loading area and wear liners, and modify transfer point if necessary. Installation ChecklistChute walls and/or wear liners are 3/8 in. above belt at tail and 3/4 in. above belt at head.Second or first I-beam of impact cradle aligns with center of loading point.An idler is installed under belt 1 in. (25 mm) before and after impact cradle.Center impact bars are centered below belt and are parallel to belt travel.Wing sections are aligned with idlers.Distance from top of center impact bars to bottom of belt surface is 1/2 in. (13 mm) max. for troughed belts and 1/4 in. (6 mm) for flat belts. Troubleshooting Martin Engineering M3493-08/13MartinImpact Cradles LD and MD This section provides product names and corresponding part numbers for Impact Cradles LD and MD. Please reference part numbers when ordering parts.Martin Impact Cradle LD Assembly, P/N 36010-XXXMartin Impact Cradle MDAssembly, P/N 36318-XXXMartin Impact Cradle MDAssembly with 5 ft. bars, P/N 36516-XXXWear LinerP/N WL-XXXXXXXXXXXX. First four Xs indicate the height of wear liner in inches; next four Xs indicate length of wear liner in inches; next three Xs indicate thickness of wear liner in inches; last X indicates wear liner material.Martin P/N 36700-XXX, for all size belts (18- to 72-in).First XX indicates belt width in inches; last X indicates standard cradle (S) or wide base cradle (W).Shim Kit: P/N 34163. Martin Engineering M3493-08/13MartinImpact Cradles LD and MDFigure 3. Martin 34° 39° (1118)See Adjustment Detail Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MD* First XX indicates Belt Width. Last X indicates Standard (S) or Wide (W) Base. NS = Not ShownFigure 3. MartinTable II. Part Numbers and Quantities, Martin Impact Cradle LDItemDescriptionPart No.Qty1Cross Support Weldment35990-XXX2Wing Support PlateTable II33Eccentric Adjustment3599464Wing Angle Right35992-R35Wing Support PlateTable II36Wing Angle Left35992-L37Bar Holder35991Table II8Urethane Impact Bar39102-4Table II9Washer Flat 1/2 Wide ZP17328Table II10Screw HHC 1/2-13NC x 1-3/4 ZP23478Table II11Washer Compression 1/211750Table II12Nut Hex Lawson Lock 1/2-13NC ZP36215Table II13Screw HHC 1/2-13NC x 1-3/4 ZP36228614Nut Hex 1/2-13NC ZP117711815Washer Flat 1/2 Narrow ZP310101216Screw HHC 1/2 - 13NC x 1-1/2 ZP117631217Mounting Hardware36229118 (NS)Label Kit34042119 (NS)Operator’s ManualM34931Part No.Dim ADim BDim CPart No.Item 2Part No.Qty ItemQty Item Item 10, 1236010-24S36.00 (914)(838)8.06 35993-2R35993-2L636183642736010-24W42.00 (1067)(991)8.06 35993-2R35993-2L636183644636010-30S42.00 (1067)(991)8.06 35993-2R35993-2L742213950136010-30W48.00 (1219)(1143)8.06 35993-2R35993-2L742213951236010-36S48.00 (1219)(1143)8.06 35993-2R35993-2L742213951236010-36W54.00 (1372)(1295)8.06 35993-2R35993-2L742213952336010-42S54.00 (1372)(1295)35993-3R35993-3L954274565636010-42W60.00 (1524)(1448)35993-3R35993-3L954274567536010-48S60.00 (1524)(1448)35993-3R35993-3L1060304873036010-48W66.00 (1676)(1600)35993-3R35993-3L10603048742 Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDFigure 4. Martin 40.50(1029)13.50(343)3.07(78)48.00(1219) See Adjustment Detail Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MD* First XX indicates Belt Width. Last X indicates Standard (S) or Wide (W) Base. NS = Not ShownFigure 4. MartinItemDescriptionPart No.Qty1Cross Support Weldment36317-XXX2Wing Support PlateTable III43Eccentric Adjustment3599484Wing Angle Right35992-R45Wing Support PlateTable III46Wing Angle Left35992-L47Bar Holder36324Table III8Urethane Impact Bar39102-4Table III9Washer Flat 1/2 Wide ZP17328Table III10Screw HHC 1/2-13NC x 1-3/4 ZP23478Table III11Washer Compression 1/211750Table III12Nut Hex Lawson Lock 1/2-13NC ZP36215Table III13Screw HHC 1/2-13NC x 1-3/4 ZP36228814Nut Hex 1/2-13NC ZP117712415Washer Flat 1/2 Narrow ZP310101616Screw HHC 1/2 - 13NC x 1-1/2 ZP117631617Mounting Hardware31033118 (NS)Label Kit34042119 (NS)Operator’s ManualM34931 Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDTable III. Part Numbers and Quantities, MartinPart No.Dim ADim BDim CPart No.Part No.Item 5Qty ItemWt.(Lbs)36318-24S8.06(205)35993-2R35993-2L648244856236318-24W(1067)8.06(205)35993-2R35993-2L648244859336318-30S(1067)8.06(205)35993-2R35993-2L756285264736318-30W(1219)(1143)8.06(205)35993-2R35993-2L756285267836318-36S(1219)(1143)8.06(205)35993-2R35993-2L756285267736318-36W(1372)(1295)8.06(205)35993-2R35993-2L756285270936318-42S(1372)(1295)8.56(217)35993-3R35993-3L972366084136318-42W(1524)(1448)8.56(217)35993-3R35993-3L972366087236318-48S(1524)(1448)8.56(217)35993-3R35993-3L1080406492636318-48W(1676)(1600)8.56(217)35993-3R35993-3L1080406495736318-54S(1676)(1600)8.81 (224)35993-4R35993-4L12964872111336318-54W(1829)(1753)8.81 (224)35993-4R35993-4L12964872114636318-60S(1829)(1753)8.81 (224)35993-4R35993-4L131045276120036318-60W(1981)(1905)8.81 (224)35993-4R35993-4L131045276123236318-66S(1981)(1905)9.06 (230)35993-5R35993-5L151206084140236318-66W(2134)(2057)9.06 (230)35993-5R35993-5L151206084143236318-72S(2134)(2057)9.06 (230)35993-5R35993-5L161286488147436318-72W(2286)(2210)9.06 (230)35993-5R35993-5L1612864881520 Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDFigure 5. Martin Impact Cradle MD Assembly with 5 ft. bars, P/N 36516-XXX (Sheet 1 of 2) Scale 1/820° Installation45° Installation36318-36S35° InstallationAdjustment Detail(minimum)Scale 3/8Adjustment Detail(maximum)Scale 3/8 11632876 15.00±.06(381)45.00(1143)60.00 (1524) ABCD 14 1819 3.07(78) Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDNS = Not ShownFigure 5. Martin Impact Cradle MD Assembly with 5 ft. bars, P/N 36516-XXX (Sheet 2 of 2)ItemDescriptionPart No.Qty1Cross Support WeldmentTable II42Right Angle Wing35992-R43Eccentric Adjustment3599484Wing Support PlateTable II35Left Wing Angle35992-L46Wing Support PlateTable II47Bar Holder (5 ft.)36519Table II8Impact Bar w/ Aluminum Track (5 ft.)33816Table II9T-Bolt 1/2 - 13NC x 1-1/231775Table II10Flat Washer 1/2 Wide ZP17328Table II11Hex Nut Lawson Lock 1/2 - 13NC ZP36215Table II12Screw HHC 1/2 - 13NC x 1-3/4 ZP36228813Compression Washer 1/211750Table II14Hex Nut 1/2 - 13NC ZP117712415Flat Washer 1/2 Narrow ZP310101616Screw HHC 1/2 - 13NC x 1-1/2 ZP117631617Mounting Hardware31033118Nut Plate37387Table II19Screw FHSC 3/8-16NC x 1.0032900Table II20 (NS)Label Kit34042121 (NS)Operator’s ManualM34931 Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDTable IV. Part Numbers and Quantities, Martin Impact Cradle MDwith 5 ft. barsPart No.Dim ADim BDim CPart No.Part No.Item 4Part No.9, 10, Qty Item18, 1936516-24S(838)(204)36317-24S35993-2R35993-2L624481264236516-24W(1067)(991)(204)36317-24W35993-2R35993-2L624481267336516-30S(1067)(991)(204)36317-30S35993-2R35993-2L728521474036516-30W(1219)(1143)(204)36317-30W35993-2R35993-2L728521477136516-36S(1219)(1143)(204)36317-36S35993-2R35993-2L728521477036516-36W(1372)(1295)(204)36317-36W35993-2R35993-2L728521480236516-42S(1372)(1295)(216)36317-42S35993-3R35993-3L936601895836516-42W(1524)(1448)(216)36317-42W35993-3R35993-3L936601898936516-48S(1524)(1448)(216)36317-48S35993-3R35993-3L10406420105636516-48W(1676)(1600)(216)36317-48W35993-3R35993-3L10406420108736516-54S(1676)63.00 (1600)(223)36317-54S35993-4R35993-4L12487224126836516-54W(1829)69.00 (1753)(223)36317-54W35993-4R35993-4L12487224130136516-60S(1829)69.00 (1753)(223)36317-60S35993-4R35993-4L13527626136736516-60W(1981)75.00 (1905)(223)36317-60W35993-4R35993-4L13527626139936516-72S(2134)81.00 (2057)(229)36317-72S35993-5R35993-5L16648832167836516-72W(2286)87.00 (2210)(229)36317-72W35993-5R35993-5L166488321724 Part Numbers Martin Engineering M3493-08/13MartinImpact Cradles LD and MDFigure 6. Conveyor Products Warning Label, P/N 23395 WARNING Lock out and/or tag out all energy sources to Cierre y/o rotule todas las fuentes de energía alLabel P/N 23395 CUIDADO conveyor system and loading system before performing any work on conveyor or conveyoraccessories. Failure tosevere injury or death. sistema transportador y al sistema de carga antesjo sobre el transportador transportador. Si nose procede asi, puede resuo muerte. Part Numbers Any product, process, or technology described here may be the subject of intellectual property rights reserved by Martin Engineering Company. Trademarks or service marks designated with the ® symbol are registered with the U.S. Patent and Trademark Office and may be proprietary in one or more countries or regions. Other trademarks and service marks belonging to Martin Engineering Company in the United States and/or other countries or regions may be designated with the “TM” and “SM” symbols. Brands, trademarks, and names of other parties, who may or may not be affiliated with, connected to, or endorsed by Martin Engineering Company, are identified wherever possible. Additional information regarding Martin Engineering Company’s intellectual property can be obtained at www.martin-eng.com/trademarks Martin Impact CradlesOperator’s Manual Go to Martin® Impact Cradles LD and MD web page Neponset, IL 61345-9766 USAwww.martin-eng.com Form No. M3493-08/13© Martin Engineering Company 2000, 2013