Conformable anti-slip surfacing, black ( Ref 510 ) 3M Commercial Care - PDF document

Conformable anti-slip surfacing, black ( Ref 510 ) 3M Commercial Care Laboratory Europe Avenue Boulé – BP 28 F-95250 Beauchamp Technical Data Supersedes : TD 472 A – July 99 EK. Page 1 / 4 The product consists of abrasive particles bonded by a tough, durable polymer to aluminium foil. The re-verse side is coated with a rubber Colour : Black Applied thickness : MIL D-17951 Ships 0.9 mm Applied weight : MIL D-17951 Ships 885 g/m² Resistance to U.V. : good Flammability : class I : Exceeds Passes Passes Smoke Density (Dm - Flaming - Non-Flaming temperature : Minimum service tempe-minus 40 °Cminus 40 °F Maximum service tempe-79 °C / 175°C Specif. Surface Condition Value Mini Rubber Dry Wet Oily Leather Dry Wet Oily Dynamic coefficient of friction : Surface Condition Value Mini Rubber Dry Wet Oily Leather Dry Wet Oily Standard Sizes : 152 mm x 610 mm (6” x 60’) Rolls : 51 mm x 18.3 m (2" x 60’) 102 mm x 18.3 m (4" x 60’) 152 mm x 18.3 m (6" x 60’) 305 mm x 18.3 m (12” x 60’) 610 mm x 18.3 m (24” x 60’) Conformable anti-slip surfacing, black ( Ref 510 ) 3M Commercial Care Laboratory Europe Avenue Boulé – BP 28 F-95250 Beauchamp Technical Data EK. Page 2 / 4 Custom Sizes : Custom sizes are available upon re-quest (minimum order quantities may apply).Water R Soap (1% Ivory Flakes in water) Detergent (1% Dreft in Bleach (5,25% sodium Hypochlorite) 1% Sodium Hydroxide NR 1% Hydrochloric Acid R 25% Sulfuric acid in water R Isopropyl Alcohol (25%) R Methyl Ethyl Ketone I Mineral Spirits NR Trichloroethylene NR Peanut Oil R Hydraulic Fluid (Skydrol 500B) Motor Oil R Gasoline (unleaded) IC Diesel fuel I 50% Anti-freeze in water R Wind screen washer fluid R R = Recommended for non continuous immersion I = Recommended for Intermittent exposure only NR = Not Recommended Note : The recommendations noted here are based on results of 7-day immersion tests bonded to stainless steel. The technical data contained herein are guidelines based upon tests and infor-mation believed to be reliable. However, for specific applications it is recommended to con-duct additional or more specific testing as per-formance properties may vary with chemical concentrations, exposure times, heat and clean-ing conditions. Packaging and Marking : 152 mm x 610 mm : 50 pcs/case Rolls : 51 mm x 18.3 m : 2 rolls/case 102 mm and wider : 1 roll/case Each case is marked with product name, size, colour and manufacturer's trade name. An installation & cleaning instruction See page 3 of this technical data sheet maintenance instructions.3M primers : - Scotch-Grip™ EC2141 - Scotch-Grip™ FB10 - Scotch-Clad™ 776 3M edge sealing compound : - Scotch-Seal™ 1103 Clear Sealant Storage conditions : It is recommended to store the product in its closed carton, preferably at a temperature between 15°C to 30°C with humidity in the range of 50% to It is recommended to use the product within 3 years from the date printed on Product durability : When exposed to pedestrian traffic only, the product will stand at least 1 million crossings. (Around 3 years if 1000 people walking over every day). Wheeled traffic is not recommended and will significantly reduce product Product Disposal : Post-consumer waste can be disposed of in appropriate containers and/or be incinerated. European code for waste disposal is : Product Origin : Made in USA and converted in France., in ISO 9002 certified plants. Conformable anti-slip surfacing, black ( Ref 510 ) 3M Commercial Care Laboratory Europe Avenue Boulé – BP 28 F-95250 Beauchamp Technical Data TD 472 B. Date : January 02 EK. Page 3/4 Make sure surface is clean, dry, smooth and Conformable: 4°C (40°F) General Purpose: 4°C (40°F) Resilient Medium: 4°C (40°F) Resilient Fine: 10°C (50°F) Repair or replace any damaged or broken surface. Remove chipped, cracked or peeled paint from surface. Use appropriate cleaner or solvent wipe to clean surface : Type of surface Bare metal, polyethylene, polypropylene Painted metal, painted wood, gel-coated fiber-epoxy floors and let dry. Porous concrete Degrease wash, rinse and let dry Painted concrete Degrease wash, rinse and let dry marble, ceramic Strip off floor finish, wash , rinse and let dry Quarry tile Degrease wash, rinse and let dry Tools needed: rubber hand roller or rubber mallet. 1. Individual pieces should be spaced a minimum of 12 mm apart and a maximum 2. Round the corners of any pieces cut from 3. Peel protective liner back about 50 mm from one end and position piece on sur-face. Note: minimize touching (contami-4. Continue to remove liner and press firmly in place as liner is removed. 5. For small pieces, peel liner off piece. Holding piece by its edges, curve it gently with the adhesive side out. Align the mid-dle of the piece over the middle of the tar-get surface and press down. 6. Finally press into firm contact with sur-face using a rubber hand roller by starting 7. For applying 3M Safety-Walk Conform-able treads, a soft rubber mallet can also be used to ensure product fully conforms 8. On steps, apply 3M Safety-Walk materi-als 12 to 15 mm from stair edge to pre-Rough or smooth, porous surfaces : Prime coat with a 3M primer is recommended Painted surfaces : 3M Safety-Walk materials can be applied on most painted surfaces which are in good condition and will adhere as well as the base paint. Painted surfaces must be thoroughly dry before the application. Treated and untreated wood : Wood surfaces must be sealed or painted before application of 3M Safety-Walk materi-als. Immersed surfaces : 3M Safety-Walk materials are not recom-mended for continuous immersion in water or for areas with constant moisture seepage. Do not bridge over joins, grouting, cracks or breaks in all surfaces. Cut into smaller pieces. Kitchen and greasy floors : Application of 3M Safety-Walk materials is not recommended for quarry tile in commer-cial kitchens. (because quarry tiles are often For extra protection from excessive moisture or liquids (not constant moisture) use 3M Scotch-Seal™ 1103 Clear Sealant to protect the edges of 3M Safety-Walk materials 1. Properly clean the floor following “sur-2. Use a paint brush and paint on a thin coat of primer where the 3M Safety-Walk materials are to be applied. 3. Allow the primed area to dry thoroughly (no evidence of stickiness or tackiness) before applying 3M Safety-Walk mate- : Primers are not generally recom-mended with the clear grade because the transparency benefit is then lost. Periodically inspect product application to Keep free of dirt and other residue that might impair functionality. General Purpose, Conformable treads should be decked-brushed regularly. Fine and Medium Resilient should be mopped or deck-brushed regularly. Use appropriate degreaser/cleaner as a gen-eral maintenance cleaner to keep material and surrounding surfaces free of soil and grease. To remove and replace worn or torn mate-1. Start by pulling up old material. Use of a heat gun and a scraper will assist in this 2. After total removal of old mate-rials, use a degreaser or solvent based cleaner to remove adhesive residues before proceeding with re-application of 3M Safety-Walk materials. Conformable anti-slip surfacing, black ( Ref 510 ) 3M Commercial Care Laboratory Europe Avenue Boulé – BP 28 F-95250 Beauchamp Technical Data TD 472 B. Date : January 02 EK. Page 4/4Typical Applications Coarse Conformable Medium Fine cultural machinery e.g excavators, trucks, cranes, Steps, stairs, ramps, scaf-folding, platforms… Ladders, stepladders, step-stools… snowmobiles, all-terrain lawn mowers… Leisure equipment and vehi-cles e.g skateboards, motor-scooters… Aerospace industry e.g cargo holds, wings… Transportation, trains, trams, craft & yachts, water skis, Swimming pool areas, diving Bath areas, showers, chang- Bathtubs Friction enhancement e.g conveyor rollers, shelf sur- Food service areas * * Not recommended for application on greasy quarry tiles. Safety-Walk General Purpose Slip-Resistant Material : Conformance to Military Specificatiwhen required.