PPT-CONTROL OF HAZARDOUS ENERGY

LOCKOUTTAGOUT OSHA 29 C FR 1910147 This material was produced under grant numbers SH223001160F17 from the Occupational Safety and Health Administration US Department of Labor It does not necessarily reflect the views or policies of the US Department of Labor nor does mention of trade names commercial products or organizations imply endorsement by the US Government. Valley City State University | Facilities Services. Introduction. What is LOCKOUT/TAG-OUT?. Lockout/Tag-out refers to a safety . procedure which is used in industry . settings . to ensure that dangerous machines are properly shut off and not started up again prior to the completion of maintenance or servicing work. . Steve Geiger, CSP. Safety & Occupational Health Manager. Naval Safety Center . steven.geiger@navy.mil. Objectives. In this course, we will cover the following:. The need for energy control procedures. The life you save, may be your own.. Control of Hazardous Energy. OSHA . 29 CFR 1910.147. LOCKOUT - TAGOUT. Workers performing service or maintenance on machinery and equipment are exposed to injuries from the unexpected energization, startup of the machinery or equipment, or release of stored energy in the equipment.. Tagout. ). CSP shall establish a program consisting of:. E. nergy control procedures. Employee training. Periodic inspections. This procedure . for the control of hazardous energy . shall . comply with the OSHA 29 CFR 1910.147 and shall clearly outline:. (LOCKOUT/TAGOUT). OSHA 29 C FR 1910-147. “This . material was produced under grant numbers SH-22300-11-60-F-17 from the Occupational Safety and Health . Administration. , U.S. Department of Labor. It does not necessarily reflect the views or policies of the U.S. Department of Labor, nor does mention of trade names, commercial products, or organizations imply endorsement by the U.S. Government. Tagout. ). . 29 CFR 1910.147. Objectives. In this course, we will cover the following:. The need for energy control procedures. Methods of lockout/tagout. Employer’s responsibilities. Employee training needs. OSHA Federal Standards. October 1, 2016 – September 30, 2017. GENERAL INDUSTRY . FY 2017. Most Frequently Cited Serious Violations in . General Industry 2017. 2. Overall 1910 MFC. Hazard Communication – Written Program. Steve Geiger, CSP. Safety & Occupational Health Manager. Naval Safety Center . steven.geiger@navy.mil. Objectives. In this course, we will cover the following:. The need for energy control procedures. Tagout. ). Report Errors to Management. CSP shall establish a program consisting of:. E. nergy control procedures. Employee training. Periodic inspections. This procedure for the control of hazardous energy shall comply with the OSHA 29 CFR 1910.147 and shall clearly outline:. OSHA’s Control of Hazardous Energy. 29 CFR 1910.147 . 29 CFR 1910.133. Administered by . Skidmore College. Objectives . Recognize hazardous energy sources. Understand responsibilities to create and maintain safe conditions. (Lockout/Tagout) Program. Mandatory Training for Administrative and Supervisory . Employees. Richard Jolliff, MS, CSP. Jenny Fuller, MS, CSP. April 9, 2015. Video: Accident without Lockout. Examples of Sources and Equipment. (Lockout/Tagout – 1910.147) “ Authorized ” - Students’ Manual A Program of the Health & Safety Department International Union, UAW Funding was pr ovided by the National Institute of Environme Chapter 51Control of Hazardous Energy Quick Start SummaryProduct ID: | Revision ID: 2299 | Date published: 18 June 2021 | Date effective: 18 June 2021 https://www-group.slac.stanford.edu/esh/eshman Environmental Health Safety EHS StandardControl Of Hazardous EnergiesIntel CorporationRev 81April 20111TABLE OF CONTENTSCOHE/LOTOIPurposeIIScopeIIIProgram RequirementsAGeneral RequirementsBLockout/Ta