ApprovalsTo stop a machine or a processFeaturesStatus information with serial TÜVNORD Functional safety dataEN ISO 138491EN 62061IECEN 6150817Up to PL eCat 4 depending upon system architec ID: 847132
Download Pdf The PPT/PDF document "Inca Tina is an emergency stop button fo..." is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.
1 Inca Tina is an emergency stop button fo
Inca Tina is an emergency stop button for panel mounting. Inca Tina is designed for installation in 22.5 mm holes in equipment cabinets. Inca Tina is to be used with Vital control module or Pluto Safety PLC.Reduced downtime All Inca Tina offer extensive indication of their status.A bright LED placed in the center of the push-button tells whether the push-button is pressed or not, and also whether the connection is interrupted before the device.All models are equipped with an information output that can be connected to, e.g., a PLC or a HMI, in order to know exactly which button has been pushed. The models with “StatusBus” functionality offer all the advantages of serial connection while still getting status information from each device.The removable terminal bl
2 ock speeds up the connection.Cost effect
ock speeds up the connection.Cost effective solutionUp to 10 Inca Tina can be connected to ONE input of a Pluto safety PLC. With a conventional 2 contact emergency stop button, two inputs would be necessary.Emergency stop button for panel mounting INCA Tina Approvals:To stop a machine or a processFeatures:Status information with serial TÜVNORD Functional safety dataEN ISO 13849-1EN 62061IEC/EN 61508-1...7Up to PL e/Cat. 4 depending upon system architectureSIL 3 depending upon system architectureSIL 3, PFHd: 4,66 10Power supplyOperating voltageTotal current consumptionInformation outputTime delay t (in/out)Voltage when normal operation(protection OK) and 24 VDC supply voltage24 VDC + 15 %, -25 %INCA 1 Tina/INCA 1S Tina: 47 mA (57 mA with max info signal out)INCA 1EC
3 Tina/INCA 1SC Tina: 23 mA (33 mA with m
Tina/INCA 1SC Tina: 23 mA (33 mA with max info signal out)Max 10 mAINCA 1 Tina/INCA 1S Tina: t 0 sINCA 1EC Tina/INCA 1SC Tina: t 0 sDynamic input: between 9 and 13 volt (RMS)Dynamic output: between 9 and 13 volt (RMS)Information output: ~23 VDCProtection classIP65, terminal block IP20Ambient temperatureStorage: -30...+70°COperation: -10...+55°CHumidity range35 to 85 % (with no icing or condensation)Housing materialPolyamide PA66, Macromelt, Polybutylenterephthalate PBT, Polypropene PP, UL 94 V0Contact materialSilver alloy, gold platedContacts5 pole terminal blockSizeSee DimensionsWeight~45 gColourYellow base, red or black buttonActuator force (E-stop button)22 ± 4NActuator travel~4 mm to latchMechanical life&#x 3-1;.90; 50.000 operationsLED on Smile Tin
4 aStatusBus LED indicationGreen: Safety d
aStatusBus LED indicationGreen: Safety device OK, safety circuit OKFlashing red-green: Safety device OK, safety circuit previously interruptedRed: Button pushed, safety circuit interruptedDouble ash, red or green: Sensor waiting for an address. Red: Button pushed. Green: Button releasedBursts of high freq. ash: Sensor identi cationSlow ash, 1 per 2 sec: During addressingHigh frequency ash: Short circuit between pin 5 and dynamic signal (pin 2 or 3)Technical data INCA Tina5 pole terminal block1 ) +24 VDC2 ) Dynamic signal input4 ) Dynamic signal output5 ) Information output** For the devices with StatusBus functionality: If the device has address 0, pin 5 is an information output. If the address is 1 to 30, pin 5 is a StatusBus I/O. The address i
5 s 0 at delivery. Use Pluto safety PLC or
s 0 at delivery. Use Pluto safety PLC or Fixa addressing unit for the addressing. See manuals.Note: Shielded cable is recommended between this unit and the rest of the safety circuit. The information channel output shall never be used for the safety purpose(s).Caution! Follow the pin numbers as labelled on the unit. All dimensions in millimeters INCA 1EC Tinawith StatusBus.INCA 1 Tinawith information output. Connection examples INCA 1EC Tina and Tina 4Awith StatusBus. Note: Terminals 5, 6, 7 and 8 in Tina 4A must be connected to each other when the StatusBus functionality is used. TypeArticle numberDescriptionC5 cable2TLA020057R0000Cable 5 x 0,34 mm + screen, by meterFront ring2TLA030054R0400Front ring, yellow, for IncaEmergency stop sign2TLA030054R0500Ø 22.5 mm, Swedis
6 h, Danish, FinnishEmergency stop sign2TL
h, Danish, FinnishEmergency stop sign2TLA030054R0600Ø 22.5 mm, English, French, German Front ring for Inca 2 ) The StatusBus functionality can be used with Pluto safety PLC only, not with Vital 1. If the device has address 0, pin 5 is an information output. If the address is 1 to 30, pin 5 is a StatusBus I/O. The address is 0 at delivery. Use Pluto safety PLC or Fixa addressing unit for the addressing. See manuals. TypeArticle numberINCA 1 Tina2TLA030054R0000INCA 1S Tina2TLA030054R0200INCA 1EC Tina2TLA030054R1400INCA 1SC Tina2TLA030054R1500Red buttonBlack buttonRemoval terminal blockReduced installation depthInformation outputStatusBus functionalityModels and ordering information Varlabergsvägen 11Tel. +46 (0) 21-32 50 00www.abb.com/jokabsafety 2TLC172092L02