/
Pace Edwards Company  Commercial Blvd Pace Edwards Company  Commercial Blvd

Pace Edwards Company Commercial Blvd - PDF document

karlyn-bohler
karlyn-bohler . @karlyn-bohler
Follow
426 views
Uploaded On 2015-05-04

Pace Edwards Company Commercial Blvd - PPT Presentation

Centralia WA 98531 800 3383697 toll free 360 7369991 main 360 7369992 fax wwwpaceedwardscom ERUBC INSTL 0711 INSTALLATION INSTRUCTIONS TABLE OF CONTENTS PACE EDWARDS brPage 2br TOOLS REQUIRED FOR ASSEMBLY BEFORE YOU START PACKAGING CONTE ID: 60812

Centralia 98531 800

Share:

Link:

Embed:

Download Presentation from below link

Download Pdf The PPT/PDF document "Pace Edwards Company Commercial Blvd" is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.


Presentation Transcript

Centralia WA 98531www.paceedwards.comERUBC INSTL 0711 INSTALLATION INSTRUCTIONS Required Tools..............................................................2Before You Start...........................................................2Optional Wiring Harness..............................................2Packaging Contents.....................................................2Hardware Kit.................................................................31. Place the Canister....................................................42. Installing the Horizontal Rails................................4-53. Installing the Release System..................................54. Installing Drain Tubes...............................................65. Install & Match Drill Horizontal rail clamps...............66. Shim the Horizontal rail clamps................................67. Bolt Down Horizontal rail clamps..............................78. Installing the Corner Blanket Guide..........................79. Installing Vertical Rails & clamps..............................810. Install the Wiring.....................................................911. Connecting the Wires to the Battery.....................1012. Mounting the Top Cover.......................................1013. Lubricate the rails.................................................1014 Installing the optional manual operation switch......11Helpful Maintenance Hints..........................................11Warranty Statement....................................................12 TABLE OF CONTENTSPACE EDWARDSRETRACTABLE UTILITY BED COVER - ELECTRIC ELECTRIC UTILITY BED COVER INSTALLATION INSTRUCTIONS HARDWARE KIT: FRONT CLAMP (x 1) CONTROL SWITCH WIRE WIRE TIES (x 6)CONTROL BATTERY WIRE GROMMET (x 2) CLAMP (x9) CLAMP BOLT (x 11) (x 11)SET TOP COVER SCREW SWIVEL WASHER HEX NUT ZP (x 1) CHANNEL #8 x ¾ PAN DRAIN TUBE FITTING (x2)Foam Washer WASHER GROMMET (x 1)SET SHEET METAL STEP 2. INSTALLING THE HORIZONTAL RAILS le) into the rail grip le) that is bolted to . You must hold the ribbed blanket out and level while sliding the rail over it and into the rail grip on the canister. t tight and need to be centered the truck bed. exing the rails inward slightly, then slide rail (FIGURE 2E THE FORWARD DRIVER SIDE RAIL CLAMP IS WIDER AND HAS A NOTCH AT THE FRONT) Slide side and a regular narrow clamp is used on the passenger side. The gap To shim, move the rail clamp and place as many of the plastic shims ll the gap. Place end. This width must not be wider at the tailgate than the canister end. to 1/8 maximum narrower at the 4 ELECTRIC RETRACTABLE UTILITY BED COVER INSTALLATION INSTRUCTIONS SAME FOR BOTH STANDARD STEP 1. PLACE THE CANISTER t is very the truck bed about 3 inches. (A folding chair works well). Pull approximately 4-5 ribs of the cover out of the canister. FIG. 1A Rail Grips Rail Ribbed 6 ELECTRIC RETRACTABLE UTILITY BED COVER INSTALLATION INSTRUCTIONS 5. INSTALL AND MATCH DRILL THE HORIZONTAL RAIL CLAMPS exing the rails inward slightly, then slide one rail clamp all the way forward against the canister on both rails about 4”-6” from the canister. (Figure 5A) Tighten the set screw 4. INSTALLING THE DRAIN TUBES First ensure that the “o” ring is in place on the drain tube end being inserted into the canister. (This will prevent water ttings into the pre-drilled holes on the underside of the canister by under the canister. 6. SHIM THE HORIZONTAL RAIL CLAMPS (IF NEEDED) To shim, move the rail clamp and place as many of the plastic shims ll the gap. ELECTRIC RETRACTABLE UTILITY BED COVER INSTALLATION INSTRUCTIONS 7 8. INSTALLING CORNER BLANKET GUIDE ush with Attach the corner channel to the horizontal rail with the 2 - 10 x ¾ BLACK SHEET METAL SCREW. Attach the corner blanket guide the the vertcal rail with the 2- 10 x ¾ BLACK SHEET METAL SCREW. G . 4A Measure the width between the rails at the canister end and then at the tailgate end. This width must not be wider at the tailgate than the canister end. The width is best if shimmed 1/16 to 1/8 maximum narrower at the With a partner on the outside of the truck to help, use the ¼-20x 1¼ Clamp Bolt, Fender washer, and ¼-20 nylock washer to secure all the clamps to the truck body. (Figure 7A & 7B) 7. BOLT DOWN HORIZONTAL RAIL CLAMPS ELECTRIC RETRACTABLE UTILITY BED COVER INSTALLATION INSTRUCTIONS 9 10. INSTALL THE WIRING the wiring exit hole in the retractable bed cover canister. Slice through the rubber grommet and wrap it around the wire harness. Work the grommet into the ½” hole and The wires are staggered in length to ease installation through the cabinet wall, plug the wires together by color.(Without the rubber cover) (Purple/ Green)You may need to drill between the cabinets for wire harness routing. (If the switch operates the cover the opposite direction that you prefer, you only need to switch the Grey Fig. 10AFig. 10B HELPFUL MAINTENANCE HINTS To assure quiet, smooth operation, apply a small amount of grease to the guide strips where the metal end of the panels and the guide strips meet. This initial application should be suf cient for a year or more. Regrease the Periodically remove the top cover and clean out the canister. To help keep the tonneau cover looking its best, we recommend washing it the same as caring for your truck nish.If you have any questions please call our Technical Support at (800) 338-3697. 14. INSTALLING THE OPTIONAL MANUAL OPERATION SWITCH rewall of the truck and pull the harness into Coil the excess wire harness and tie out of the way. (If cover runs in opposite direction than you prefer, just switch the Grey and Purple wires)Your Utility Bed Cover should run at this time. Check for correct operation by operating all switches installed. BL1120) ELECTRIC RETRACTABLE UTILITY BED COVER INSTALLATION INSTRUCTIONS 11