VGZ-025 / 100105.0VG650ELG MOUNTAINEER - PDF document

VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 3 ASSEMBLY INSTRUCTIONSNOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of TOOLS AND MATERIALS REQUIRED FOR INSTALLATION foot Folding Rule or Tape Measure MATERIALS(NOTE: The following items are NOT included with your stove)listed Type HT chimney.CAUTION: STOVE IS HEAVY. MAKE SURE YOUHAVE ADEQUATE HELP AND USE PROPERSTOVE.Uncrate the stove and remove all cardboard andbase (#18) and pedestal top (#14) from the car-ton. (Save cardboard for further assembly.)2.Remove parts from inside stove. Parts include:3.Using the self-tapping screws provided in the5.Place pedestal side/front assembly on top ofbase. Align holes in pedestal sides with holes6.Carefully tip the pedestal base backward and7.Tip the pedestal base assembly upright. 8.Set the pedestal drawer slide (16) inside thefloor protector.10.Place pedestal top (#14) onto pedestal base as-12.Carefully position stove body (#1) onto ped-HEAVY. Make sure you have adequate helpproper lifting techniques.mounting studs and tighten securely.13.Attach rear deflector to the rear side corners of14.Attach blower assembly (#3) to back of reardeflector. NOTE: Make sure ceramic gasket isassembly..damper installation on page 6] and secure totop surface of stove using machine screws.NOTE: After installation damper must be able VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 5 18-1/2"18-1/2"CORNER CLEARANCES LOCATING STOVE continuedÉFig. 3a Ð Front ViewFig. 3b Ð Side ViewCAUTION: KEEP FURNISHINGS AND OTHERCOMBUSTIBLE MATERIALS AWAY FROM THESTOVE.NOTE: BEFORE FIRING WOODSTOVE SLIDEFIREBRICKS TOWARDS THE REAR SO NO Fig. 2 Ð Top View VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 7 MASONRY CHIMNEYBefore using an existing masonry chimney,clean the chimney, inspect the flue liner and makerepairs before attaching the stove. The connector1). As a means of exhausting smoke and flue2). The chimney provides ÒdraftÓ which allowsNOTICE: Always provide a source of freshprovided by the chimney. To achieve proper draftrequirements detailed in figures 7Ð9. A minimumof 0.05 w.c. (measured in water column) is requiredfor proper drafting to prevent back puffing, smokean adverse effect on the draft. The manufacturerIMPORTANT Installation PointsSize chimney flue to stove collar. This stove2.Never connect this unit to a chimney serv-4.Never use a chimney to ventilate a cellarFig. 7 - Chimney Construction Through Attic Space chimney, consult a qualified mason or chimneydealer. The installation must conform to local build-ing and fire codes and latest edition of NFPA 211.chimney, close it tightly. CHIMNEYFLUE 5/8" TILECHIMNEY MASONRY 6ý ROUND24 ga. BLACKCONNECTORSTOVEPIPE BELOWENTRY VG650ELG MOUNTAINEERª Fig. 8 - Chimney Construction Through Roof Through Masonry WallCHIMNEY CONNECTIONS continued ÉMANUFACTURED CHIMNEYREFER TO CHIMNEY AND CHIMNEYCONNECTOR MAKERÕS INSTRUCTIONSFOR INSTALLATION AND USE.HT. Chimney made to this listing is High Tem-perature rated to 2100 degrees Fahrenheit. Usechimney from only one manufacturer. Never mixmanufacturerÕs stated requirements and clearances.Use the chimney manufacturerÕs attic guards, roofWhen using a pre-existing chimney, have itÕsters, hardware stores, and HVAC supply stores.tion on-line. See, www.duravent.com,www.selkirkinc.com, or www.mtlfab.com.VENTING TO EXISTING FIREPLACEexisting fireplace for stove use. Usually, safe con-more work than using a prefabricated chimney. The Continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 9 CHIMNEY CONNECTIONS continued Ébrickwork of a chimney. If a chimney does not havea liner, or it is damaged, have it relined by a pro-DO NOT USE a chimney that is un-garding the condition of the chimney, consult aqualified licensed contractor, qualified engineer,knowledgable inspector. Consult your insuranceclearance fireplaceÓ category. These consist ofmultilayered metal construction. They are designeddorsements from nationally recognized organiza-tions for use as fireplaces, they have not been testedmanufacturerÕs warranty.1/4Ó firebox liner, an air chamber in connectionwith 8Ó of masonry. These can be safely used withwood burning stoves. They contain all the essen- FIREPLACE INSTALLATIONisting masonry chimney (figure 12 ÒType AÓ fire-proved method of installation. This is a compli-should only by done by a qualified installer.1.An entry hole must be cut through the masonryand tile liner with minimal damage to the liner.try position. When locating the stove and stove-3.Secure the thimble with refractory mortar. The4.Install the stovepipe into the thimble as far as5.A small airspace (about 1/2Ó) should remain damper, throat, smoke shelf, and smokechamber. Many look identical to ma-manner. Continued on nwxt page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 11 6.Close the door and secure tightly.Adjust the draft damper control. The moreclosed the slower the fire will burn. The more8.Do not overfire the stove.stead of piling large quantities of fuel at one time.occur in the chimney.1.Always open draft damper before opening thefeed door.2.When adding fuel be careful not to smothermodels with glass door.3.Close the feed door and secure tightly.4.Adjust the draft damper control.Empty ashes regularly. Do not allow ashes7.Do not overfire the stove.CAUTION: DO NOT OVERFIRE APPLIANCE.YOU ARE OVERFIRING IF THE CHIMNEYCONNECTORS OR STOVE GLOWS RED.CLOSE THE DOOR AND SHUT FLUE DAMPERIMMEDIATELY TO REDUCE THE AIR SUPPLYTHE FIRE. THIS WILL SLOW DOWN THECAUTION: SLOW BURNING FIRES ANDEXTENDED USE MAY CAUSE EXCESSIVECREOSOTE BUILDUP. IGNITION OF CREO-SOTE BUILDUP OR OVERFIRING MAY CAUSEEXTREMELY HOT AND MAY IGNITESURROUNDING MATERIALS. IN CASE OF ACHIMNEY FIRE CALL THE FIRE DEPARTMENTIMMEDIATELY. OPERATING continued ÉOPERATING TIPS1.Burn with air control open for several minutesat numerous intervals throughout the day dur-over-fire the unit.2.Burn stove with air inlet control wide open forwood. This allows wood to achieve the char-BURN ONLY SEASONED WOOD. Avoidhas been dried for at least one year.4.A small fire is preferable to a large smoldering5.Establish a routine for the handling of fuel,ARNING: IN CASE OF CHIMNEY FIRE(1) CLOSE AIR INLET CONTROL (2) GET OUTOF THE HOUSE (3) CALL THE FIRE DEPART-MENT. Draft is a function of the chimney, not thestove Ñ do not expect the stove to draw. Smokethat the chimney is NOT functioning properly.1.The connector stovepipe may be pushedinto the chimney too far, stopping the draft.2.If the chimney is operating too cool, waterblock the chimney. Operate the stove at a fire level VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 13 When wood is burned slowly, it produces tarand other organic vapors which combine with ex-pelled moisture to form creosote. The creosoteof a slow-burning fire. As a result, creosote resi- cal hardware retailer.chimney connector should glow red, reduce the CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-TION OF WALL STUDS OR RAFTERS WHICHWERE ASSUMED TO BE A SAFE DISTANCEFROM THE CHIMNEY. IF A CHIMNEY FIRE HASOCCURRED, HAVE YOUR CHIMNEY IN-SPECTED BY A QUALIFIED EXPERT BEFOREfire in the firebox may be smothered by pour-ing a large quantity of coarse salt, baking soda, orWIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 15 ORDERING PARTS - VG650ELG MOUNTAINEER STOVE Part No.DescriptionQty.Door Frame..................................................13/8Ó dia. Fiberglass Glass Gasket................110High-Temp Ceramic Glass...........................1Glass Retainer............................................1127Retainer Screws..........................................1128Complete Door Assembly (less handle).......1 GLASS, WEAR THICK GLOVES AND SAFETYGLASSES. KEEP CHILDREN AWAY ANDDISCARD BROKEN GLASS SAFELY.1.Be sure stove has cooled before beginning.2.Using a screwdriver, remove all screws (#27)and retainers (#11) holding glass.Remove glass (#10). Replace with high-temperature ceramic glass only.Reinstall glass, gasket and retainers. Whenglass surface. Abrasives can damage the glass VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 17 ration from clay liner to combustibles. The fireclay linerB.Insulated SleeveC.Ventilated ThimbleSheet steel chimney connector, minimum 24 gauge inthickness, with a ventilated thimble, minimum 24 gaugeD.Chimney Section Pass-throughan inside diameter 2-inch larger than the chimney con-ney section and combustibles. Minimum length of chim-with sheet steel support securely fastened to wallsurfaces of minimum 24 gauge thickness. Fasteners usedchimney flue liner.CHIMNEY CONNECTOR SYSTEMS & CLEARANCES VG650ELG MOUNTAINEERª and in good repair. Have the chimney inspectedby the fire department or a qualified inspector.ommend a qualified inspector.10.Creosote or soot may build up in the chimneying season and clean if necessary. (See Chim-CALL THE FIRE DEPARTMENT IMME-DIATELY! 12.To prevent injury, do not allow anyone to use14.Ashes should not be allowed to accumulateabove sides of ash drawer. Dispose of ashes incooled. The ashes may be buried in the groundor picked up by a refuse collector.give off some smoke and an odor whilefire box. This should disappear after a shortas needed to clear smoke and/or odor. Paintor abuse. When installing your stove, use care 18.The walls of the firebox may become slightlydistorted after a period of use. A slight distor-tion will not affect the operation of the stove.19.If small children will be in the same room asNEVER LEAVE SMALLCHILDREN UNSUPERVISED22.While in operation, keep the feed door closedNO NOT ELEVATE FIRE! Build fire directlyon the bottom of the firebox. This stove has26.For further information on using your stovesafely, obtain a copy of the National FireProtection Association (NFPA) publication,ÒUsing Coal and Wood Stoves SafelyÓ NFPANo. HS-10-1978. The address of the NFPA isBatterymarch Park, Quincy, MA 02269.NOTE: A PROFESSIONAL, LICENSED HEATINGAND COOLING CONTRACTOR MUSTBE CONSULTED IF YOU HAVE QUESTIONSREGARDING THE INSTALLATION OF THISSOLID FUEL BURNING APPLIANCE. VG650ELG MOUNTAINEERª and in good repair. Have the chimney inspectedby the fire department or a qualified inspector.ommend a qualified inspector.10.Creosote or soot may build up in the chimneying season and clean if necessary. (See Chim-CALL THE FIRE DEPARTMENT IMME-DIATELY! 12.To prevent injury, do not allow anyone to use14.Ashes should not be allowed to accumulateabove sides of ash drawer. Dispose of ashes incooled. The ashes may be buried in the groundor picked up by a refuse collector.give off some smoke and an odor whilefire box. This should disappear after a shortas needed to clear smoke and/or odor. Paintor abuse. When installing your stove, use care 18.The walls of the firebox may become slightlydistorted after a period of use. A slight distor-tion will not affect the operation of the stove.19.If small children will be in the same room asNEVER LEAVE SMALLCHILDREN UNSUPERVISED22.While in operation, keep the feed door closedO NOT ELEVATE FIRE! Build fire directlyon the bottom of the firebox. This stove has26.For further information on using your stovesafely, obtain a copy of the National FireProtection Association (NFPA) publication,ÒUsing Coal and Wood Stoves SafelyÓ NFPANo. HS-10-1978. The address of the NFPA isBatterymarch Park, Quincy, MA 02269.NOTE: A PROFESSIONAL, LICENSED HEATINGAND COOLING CONTRACTOR MUSTBE CONSULTED IF YOU HAVE QUESTIONSREGARDING THE INSTALLATION OF THISSOLID FUEL BURNING APPLIANCE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG & VG651ELG Owners Manual (save this manual for future reference) continued on next page VG650ELG MOUNTAINEERª and in good repair. Have the chimney inspectedby the fire department or a qualified inspector.ommend a qualified inspector.10.Creosote or soot may build up in the chimneying season and clean if necessary. (See Chim-CALL THE FIRE DEPARTMENT IMME-DIATELY! 12.To prevent injury, do not allow anyone to use14.Ashes should not be allowed to accumulateabove sides of ash drawer. Dispose of ashes incooled. The ashes may be buried in the groundor picked up by a refuse collector.give off some smoke and an odor whilefire box. This should disappear after a shortas needed to clear smoke and/or odor. Paintor abuse. When installing your stove, use care 18.The walls of the firebox may become slightlydistorted after a period of use. A slight distor-tion will not affect the operation of the stove.19.If small children will be in the same room asNEVER LEAVE SMALLCHILDREN UNSUPERVISED22.While in operation, keep the feed door closedO NOT ELEVATE FIRE! Build fire directlyon the bottom of the firebox. This stove has26.For further information on using your stovesafely, obtain a copy of the National FireProtection Association (NFPA) publication,ÒUsing Coal and Wood Stoves SafelyÓ NFPANo. HS-10-1978. The address of the NFPA isBatterymarch Park, Quincy, MA 02269.NOTE: A PROFESSIONAL, LICENSED HEATINGAND COOLING CONTRACTOR MUSTBE CONSULTED IF YOU HAVE QUESTIONSREGARDING THE INSTALLATION OF THISSOLID FUEL BURNING APPLIANCE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 3 ASSEMBLY INSTRUCTIONSNOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of TOOLS AND MATERIALS REQUIRED FOR INSTALLATION foot Folding Rule or Tape Measure MATERIALS(NOTE: The following items are NOT included with your stove)listed Type HT chimney.CAUTION: STOVE IS HEAVY. MAKE SURE YOUHAVE ADEQUATE HELP AND USE PROPERSTOVE.base (#18) and pedestal top (#14) from the car-ton. (Save cardboard for further assembly.)2.Remove parts from inside stove. Parts include:3.Using the self-tapping screws provided in the5.Place pedestal side/front assembly on top ofbase. Align holes in pedestal sides with holes6.Carefully tip the pedestal base backward and7.Tip the pedestal base assembly upright. 8.Set the pedestal drawer slide (16) inside thefloor protector.10.Place pedestal top (#14) onto pedestal base as-12.Carefully position stove body (#1) onto ped-HEAVY. Make sure you have adequate helpproper lifting techniques.mounting studs and tighten securely.13.Attach rear deflector to the rear side corners of14.Attach blower assembly (#3) to back of reardeflector. NOTE: Make sure ceramic gasket isassembly..damper installation on page 6] and secure totop surface of stove using machine screws.NOTE: After installation damper must be able VG650ELG MOUNTAINEERª PIPE CONNECTOR INSTALLATION1.The crimped end of the stovepipe fits insidethe stove flue collar. Install additional pipe and3.You must have at least 18 inches of clearance4.The pipe cannot extend into the chimney flue6.It is recommended that no more than two (2)smoke spillage. Where possible, use onlycorrugated (nonadjustable) elbows. These7.The connector pipe must not pass through anspace, or floor, ceiling, wall or combustibletems & Clearances, page 17). A UL 103 HTa chimney - a house fire could result. CORRECTWRONGWRONG NOTE: STOVE PIPE IS PURCHASE, VISIT YOUR LOCAL HARDWARE,ÒLOCATING STOVEÓ PAGE 4 FOR ADDITIONALSPECIFICATIONS.DAMPER INSTALLATION 1. Remove damper from collar by pulling handle2.Attach damper gasket to bottom of collar.3.Position collar onto hole in stove top and align4.Secure the collar to stove with bolts and nuts5.Install damper on angle into collar as shown indamper and out the opposite side of collar.NOTE: After installation, damper must be able VG650ELG MOUNTAINEERª Fig. 8 - Chimney Construction Through Roof Through Masonry WallMANUFACTURED CHIMNEYREFER TO CHIMNEY AND CHIMNEYCONNECTOR MAKERÕS INSTRUCTIONSFOR INSTALLATION AND USE.HT. Chimney made to this listing is High Tem-chimney from only one manufacturer. Never mixmanufacturerÕs stated requirements and clearances.Use the chimney manufacturerÕs attic guards, roofWhen using a pre-existing chimney, have itÕsters, hardware stores, and HVAC supply stores.tion on-line. See, www.duravent.com,www.selkirkinc.com, or www.mtlfab.com.VENTING TO EXISTING FIREPLACEexisting fireplace for stove use. Usually, safe con-more work than using a prefabricated chimney. The Continued on next page VG650ELG MOUNTAINEERª OPERATING INSTRUCTIONSWOOD FUEL ONLY!burning efficiency. Wood should be stored in a dry,NOTICE: USE SOLID WOOD MATERIALS ONLY.FLUIDS. DO NOT USE COAL THIS STOVE ISNOT DESIGNED TO ACCOMMODATE THE AIRFLOW (DRAFT) NECESSARY TO PROPERLYELEVATE FIRE OR USE GRATES OR AND-IRONS. BUILD FIRE DIRECTLY ON BOTTOM OF1.Open draft damper fully to provide maximum2.Open the feed door and place several wads of3.Lay small stacks of kindling on the paper to4.Light the paper and kindling, close the doorand secure tightly.5.Add fuel after fire is burning briskly. Use careDO NOT STORE WOOD ON FLOOR PROTEC-OR, UNDERNEATH STOVEPIPE OR ANY-FROM COMBUSTIBLE SURFACES SPECIFIEDFOR THIS STOVE.OVERFIRING MAY CAUSE A HOUSE FIRE.YOU ARE OVERFIRING IF A UNIT OR CHIMNEYCONNECTOR GLOWS RED.OPERATING SAFETY PRECAUTIONS1.NEVER OVERFIRE THIS STOVE BY BUILD-ING EXCESSIVELY HOT FIRES AS A HOUSE/BUILDING FIRE MAY RESULT. YOU ARE OVER-FIRING THE STOVE IF UNIT OR STOVEPIPEBEGINS TO GLOW OR TURN RED.2.NEVER BUILD EXTREMELY LARGE FIRESIN THIS TYPE OF STOVE AS DAMAGE TO THESTOVE OR SMOKE LEAKAGE MAY RESULT3.ON MODELS WITH GLASS DOOR, DO NOTBUILD FIRE TOO CLOSE TO GLASS.4.UNIT IS HOT WHILE IN OPERATION. KEEPCHILDREN, CLOTHING, AND FURNITURECONTACT MAY CAUSE SKIN BURNS. DONOT TOUCH THE STOVE AFTER FIRING UNTILPROVIDE AIR INTO THE ROOM FORINSPECT STOVEPIPE EVERY 60 DAYS.REPLACE IMMEDIATELY IF STOVEPIPE ISRUSTING OR LEAKING SMOKE INTO THE 6.Secure and seal the damper in the closed posi-or furnace cement. Also check to see if theit is closed and sealed as well. A leaky cleanoutwill greatly reduce draft efficiency.the National Fire Protection Association (NFPA)and request a copy of the latest editions of NFPAStandard 211 and NFPA Standard 908. Their Battery March Park, Quincy, MA 02269. LAR FLAMMABLE LIQUIDS TO START ORÒFRESHEN-UPÓ A FIRE IN THE STOVE.KEEP ALL FLAMMABLE LIQUIDS,ESPECIALLY GASOLINE, OUT OF THEVICINITY OF THE HEATER Ñ WHETHER IN USEOR IN STORAGE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 11 6.Close the door and secure tightly.Adjust the draft damper control. The moreclosed the slower the fire will burn. The more8.Do not overfire the stove.stead of piling large quantities of fuel at one time.occur in the chimney.1.Always open draft damper before opening thefeed door.2.When adding fuel be careful not to smothermodels with glass door.3.Close the feed door and secure tightly.4.Adjust the draft damper control.Empty ashes regularly. Do not allow ashes7.Do not overfire the stove.CAUTION: DO NOT OVERFIRE APPLIANCE.YOU ARE OVERFIRING IF THE CHIMNEYCONNECTORS OR STOVE GLOWS RED.CLOSE THE DOOR AND SHUT FLUE DAMPERIMMEDIATELY TO REDUCE THE AIR SUPPLYTHE FIRE. THIS WILL SLOW DOWN THECAUTION: SLOW BURNING FIRES ANDEXTENDED USE MAY CAUSE EXCESSIVECREOSOTE BUILDUP. IGNITION OF CREO-SOTE BUILDUP OR OVERFIRING MAY CAUSEEXTREMELY HOT AND MAY IGNITESURROUNDING MATERIALS. IN CASE OF ACHIMNEY FIRE CALL THE FIRE DEPARTMENTIMMEDIATELY. OPERATING continued ÉOPERATING TIPS1.Burn with air control open for several minutesat numerous intervals throughout the day dur-over-fire the unit.2.Burn stove with air inlet control wide open forwood. This allows wood to achieve the char-BURN ONLY SEASONED WOOD. Avoidhas been dried for at least one year.4.A small fire is preferable to a large smoldering5.Establish a routine for the handling of fuel,ARNING: IN CASE OF CHIMNEY FIRE(1) CLOSE AIR INLET CONTROL (2) GET OUTOF THE HOUSE (3) CALL THE FIRE DEPART-MENT. Draft is a function of the chimney, not thestove Ñ do not expect the stove to draw. Smokethat the chimney is NOT functioning properly.1.The connector stovepipe may be pushedinto the chimney too far, stopping the draft.2.If the chimney is operating too cool, waterblock the chimney. Operate the stove at a fire level VG650ELG MOUNTAINEERª SERVICE HINTS continued É 3.If the fire burns well but sometimes cre-ates excessive smoke or burns slowly, it may beother part of the house or a nearby tree. The windsmoke. The top of the chimney should be at leastNOTE: A DRAFT READING OF 0.05 TO 0.06 W.C.(WATER COLUMN) IS SUGGESTED FORPROPER BURNING OF THIS STOVE.2.Do not slam the door or otherwise impact theglass. When closing doors, make sure that logs3.Do not build fires against (or that might fall4.Do not clean the glass with materials that may5.Never attempt to clean the glass while the unitis hot. If deposits are not very heavy, normal6.Never put substances which can ignite explo-cleaning products for wood stoves include, A.W.Perkins Co. (www.awperkins.com) or RutlandProducts (www.rutland.com). CAUTION: REPLACE GLASS ONLY WITH 5MMHIGH TEMPERATURE CERAMIC GLASS OFGlass Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove screw and glass clip. (See parts list3.Lift glass out from glass clip.4.Remove old gasket and clean glass.5.Replace new gasket starting at the bottom of6.Trim to length and butt ends together.7.Replace glass into door, being sure not to over-provides glass and door seal may lose itÕs resil-diately.Door Gasket Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove old door gasket and clean channel.3.Using an approved, high temperature gasket4.Starting at hinge side of door, work 3/8-inchdiameter fiberglass gasket material into chan-5.Close door and allow three to four hours for VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 13 When wood is burned slowly, it produces tarand other organic vapors which combine with ex-pelled moisture to form creosote. The creosoteof a slow-burning fire. As a result, creosote resi- cal hardware retailer. CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-TION OF WALL STUDS OR RAFTERS WHICHWERE ASSUMED TO BE A SAFE DISTANCEFROM THE CHIMNEY. IF A CHIMNEY FIRE HASOCCURRED, HAVE YOUR CHIMNEY IN-SPECTED BY A QUALIFIED EXPERT BEFOREfire in the firebox may be smothered by pour-ing a large quantity of coarse salt, baking soda, orWIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE VG650ELG MOUNTAINEERª FLOOR PROTECTOR MATERIAL CALCULATIONSThis stove has been tested for and must be installed on a floor protector with the proper Thermaltested requirements. The following instructions provide the proper information and formulas for con-1.Convert material specifications to R-value:R = 1/k x T2.Determine the R-value of proposed alternate floor protector:3.If the overall R-value of the floor protector system is equal to or greater than the floor protectorF)(mF)(m)(K)(hr)(ft)(BtuWStep 1:Convert specs to R-value.R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = RspecsStep 3: Add R-values of components to get total R-value of systemRsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 17 ration from clay liner to combustibles. The fireclay linerB.Insulated SleeveC.Ventilated ThimbleSheet steel chimney connector, minimum 24 gauge inD.Chimney Section Pass-throughan inside diameter 2-inch larger than the chimney con-chimney flue liner.CHIMNEY CONNECTOR SYSTEMS & CLEARANCES VG650ELG MOUNTAINEERª 400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 COMPANY TESTIMONY:ÒFOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVERBELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFEÓThis Vogelzang heating appliance is safe when installed properly and will provide you with yearsof service. However, always exercise good judgement when you are using this stove. You are dealing Steve Vogelzang Proprietor DO USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 9 brickwork of a chimney. If a chimney does not havea liner, or it is damaged, have it relined by a pro-garding the condition of the chimney, consult aqualified licensed contractor, qualified engineer,knowledgable inspector. Consult your insuranceclearance fireplaceÓ category. These consist ofmultilayered metal construction. They are designeddorsements from nationally recognized organiza-manufacturerÕs warranty.1/4Ó firebox liner, an air chamber in connectionwith 8Ó of masonry. These can be safely used withwood burning stoves. They contain all the essen- FIREPLACE INSTALLATION ÒType AÓ fire-proved method of installation. This is a compli-should only by done by a qualified installer.1.An entry hole must be cut through the masonryand tile liner with minimal damage to the liner.try position. When locating the stove and stove-3.Secure the thimble with refractory mortar. The4.Install the stovepipe into the thimble as far as5.A small airspace (about 1/2Ó) should remain damper, throat, smoke shelf, and smokechamber. Many look identical to ma-manner. Continued on nwxt page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG & VG651ELG Owners Manual (save this manual for future reference) continued on next page VG650ELG MOUNTAINEERª and in good repair. Have the chimney inspectedby the fire department or a qualified inspector.ommend a qualified inspector.10.Creosote or soot may build up in the chimneying season and clean if necessary. (See Chim-CALL THE FIRE DEPARTMENT IMME-DIATELY! 12.To prevent injury, do not allow anyone to use14.Ashes should not be allowed to accumulateabove sides of ash drawer. Dispose of ashes incooled. The ashes may be buried in the groundor picked up by a refuse collector.give off some smoke and an odor whilefire box. This should disappear after a shortas needed to clear smoke and/or odor. Paintor abuse. When installing your stove, use care 18.The walls of the firebox may become slightlydistorted after a period of use. A slight distor-tion will not affect the operation of the stove.19.If small children will be in the same room asNEVER LEAVE SMALLCHILDREN UNSUPERVISED22.While in operation, keep the feed door closedO NOT ELEVATE FIRE! Build fire directlyon the bottom of the firebox. This stove has26.For further information on using your stovesafely, obtain a copy of the National FireProtection Association (NFPA) publication,ÒUsing Coal and Wood Stoves SafelyÓ NFPANo. HS-10-1978. The address of the NFPA isBatterymarch Park, Quincy, MA 02269.NOTE: A PROFESSIONAL, LICENSED HEATINGAND COOLING CONTRACTOR MUSTBE CONSULTED IF YOU HAVE QUESTIONSREGARDING THE INSTALLATION OF THISSOLID FUEL BURNING APPLIANCE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 3 ASSEMBLY INSTRUCTIONSNOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of TOOLS AND MATERIALS REQUIRED FOR INSTALLATION foot Folding Rule or Tape Measure MATERIALS(NOTE: The following items are NOT included with your stove)listed Type HT chimney.CAUTION: STOVE IS HEAVY. MAKE SURE YOUHAVE ADEQUATE HELP AND USE PROPERSTOVE.base (#18) and pedestal top (#14) from the car-ton. (Save cardboard for further assembly.)2.Remove parts from inside stove. Parts include:3.Using the self-tapping screws provided in the5.Place pedestal side/front assembly on top ofbase. Align holes in pedestal sides with holes6.Carefully tip the pedestal base backward and7.Tip the pedestal base assembly upright. 8.Set the pedestal drawer slide (16) inside thefloor protector.10.Place pedestal top (#14) onto pedestal base as-12.Carefully position stove body (#1) onto ped-HEAVY. Make sure you have adequate helpproper lifting techniques.mounting studs and tighten securely.13.Attach rear deflector to the rear side corners of14.Attach blower assembly (#3) to back of reardeflector. NOTE: Make sure ceramic gasket isassembly..damper installation on page 6] and secure totop surface of stove using machine screws.NOTE: After installation damper must be able VG650ELG MOUNTAINEERª PIPE CONNECTOR INSTALLATION1.The crimped end of the stovepipe fits insidethe stove flue collar. Install additional pipe and3.You must have at least 18 inches of clearance4.The pipe cannot extend into the chimney flue6.It is recommended that no more than two (2)smoke spillage. Where possible, use onlycorrugated (nonadjustable) elbows. These7.The connector pipe must not pass through anspace, or floor, ceiling, wall or combustibletems & Clearances, page 17). A UL 103 HTa chimney - a house fire could result. CORRECTWRONGWRONG NOTE: STOVE PIPE IS PURCHASE, VISIT YOUR LOCAL HARDWARE,ÒLOCATING STOVEÓ PAGE 4 FOR ADDITIONALSPECIFICATIONS.DAMPER INSTALLATION 1. Remove damper from collar by pulling handle2.Attach damper gasket to bottom of collar.3.Position collar onto hole in stove top and align4.Secure the collar to stove with bolts and nuts5.Install damper on angle into collar as shown indamper and out the opposite side of collar.NOTE: After installation, damper must be able VG650ELG MOUNTAINEERª Fig. 8 - Chimney Construction Through Roof Through Masonry WallMANUFACTURED CHIMNEYREFER TO CHIMNEY AND CHIMNEYCONNECTOR MAKERÕS INSTRUCTIONSFOR INSTALLATION AND USE.HT. Chimney made to this listing is High Tem-chimney from only one manufacturer. Never mixmanufacturerÕs stated requirements and clearances.Use the chimney manufacturerÕs attic guards, roofWhen using a pre-existing chimney, have itÕsters, hardware stores, and HVAC supply stores.tion on-line. See, www.duravent.com,www.selkirkinc.com, or www.mtlfab.com.VENTING TO EXISTING FIREPLACEexisting fireplace for stove use. Usually, safe con-more work than using a prefabricated chimney. The Continued on next page VG650ELG MOUNTAINEERª OPERATING INSTRUCTIONSWOOD FUEL ONLY!burning efficiency. Wood should be stored in a dry,NOTICE: USE SOLID WOOD MATERIALS ONLY.FLUIDS. DO NOT USE COAL THIS STOVE ISNOT DESIGNED TO ACCOMMODATE THE AIRFLOW (DRAFT) NECESSARY TO PROPERLYELEVATE FIRE OR USE GRATES OR AND-IRONS. BUILD FIRE DIRECTLY ON BOTTOM OF1.Open draft damper fully to provide maximum2.Open the feed door and place several wads of3.Lay small stacks of kindling on the paper to4.Light the paper and kindling, close the doorand secure tightly.5.Add fuel after fire is burning briskly. Use careDO NOT STORE WOOD ON FLOOR PROTEC-OR, UNDERNEATH STOVEPIPE OR ANY-FROM COMBUSTIBLE SURFACES SPECIFIEDFOR THIS STOVE.OVERFIRING MAY CAUSE A HOUSE FIRE.YOU ARE OVERFIRING IF A UNIT OR CHIMNEYCONNECTOR GLOWS RED.OPERATING SAFETY PRECAUTIONS1.NEVER OVERFIRE THIS STOVE BY BUILD-ING EXCESSIVELY HOT FIRES AS A HOUSE/BUILDING FIRE MAY RESULT. YOU ARE OVER-FIRING THE STOVE IF UNIT OR STOVEPIPEBEGINS TO GLOW OR TURN RED.2.NEVER BUILD EXTREMELY LARGE FIRESIN THIS TYPE OF STOVE AS DAMAGE TO THESTOVE OR SMOKE LEAKAGE MAY RESULT3.ON MODELS WITH GLASS DOOR, DO NOTBUILD FIRE TOO CLOSE TO GLASS.4.UNIT IS HOT WHILE IN OPERATION. KEEPCHILDREN, CLOTHING, AND FURNITURECONTACT MAY CAUSE SKIN BURNS. DONOT TOUCH THE STOVE AFTER FIRING UNTILPROVIDE AIR INTO THE ROOM FORINSPECT STOVEPIPE EVERY 60 DAYS.REPLACE IMMEDIATELY IF STOVEPIPE ISRUSTING OR LEAKING SMOKE INTO THE 6.Secure and seal the damper in the closed posi-or furnace cement. Also check to see if theit is closed and sealed as well. A leaky cleanoutwill greatly reduce draft efficiency.the National Fire Protection Association (NFPA)and request a copy of the latest editions of NFPAStandard 211 and NFPA Standard 908. Their Battery March Park, Quincy, MA 02269. LAR FLAMMABLE LIQUIDS TO START ORÒFRESHEN-UPÓ A FIRE IN THE STOVE.KEEP ALL FLAMMABLE LIQUIDS,ESPECIALLY GASOLINE, OUT OF THEVICINITY OF THE HEATER Ñ WHETHER IN USEOR IN STORAGE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 11 6.Close the door and secure tightly.Adjust the draft damper control. The moreclosed the slower the fire will burn. The more8.Do not overfire the stove.stead of piling large quantities of fuel at one time.occur in the chimney.1.Always open draft damper before opening thefeed door.2.When adding fuel be careful not to smothermodels with glass door.3.Close the feed door and secure tightly.4.Adjust the draft damper control.Empty ashes regularly. Do not allow ashes7.Do not overfire the stove.CAUTION: DO NOT OVERFIRE APPLIANCE.YOU ARE OVERFIRING IF THE CHIMNEYCONNECTORS OR STOVE GLOWS RED.CLOSE THE DOOR AND SHUT FLUE DAMPERIMMEDIATELY TO REDUCE THE AIR SUPPLYTHE FIRE. THIS WILL SLOW DOWN THECAUTION: SLOW BURNING FIRES ANDEXTENDED USE MAY CAUSE EXCESSIVECREOSOTE BUILDUP. IGNITION OF CREO-SOTE BUILDUP OR OVERFIRING MAY CAUSEEXTREMELY HOT AND MAY IGNITESURROUNDING MATERIALS. IN CASE OF ACHIMNEY FIRE CALL THE FIRE DEPARTMENTIMMEDIATELY. OPERATING continued ÉOPERATING TIPS1.Burn with air control open for several minutesat numerous intervals throughout the day dur-over-fire the unit.2.Burn stove with air inlet control wide open forwood. This allows wood to achieve the char-BURN ONLY SEASONED WOOD. Avoidhas been dried for at least one year.4.A small fire is preferable to a large smoldering5.Establish a routine for the handling of fuel,ARNING: IN CASE OF CHIMNEY FIRE(1) CLOSE AIR INLET CONTROL (2) GET OUTOF THE HOUSE (3) CALL THE FIRE DEPART-MENT. Draft is a function of the chimney, not thestove Ñ do not expect the stove to draw. Smokethat the chimney is NOT functioning properly.1.The connector stovepipe may be pushedinto the chimney too far, stopping the draft.2.If the chimney is operating too cool, waterblock the chimney. Operate the stove at a fire level VG650ELG MOUNTAINEERª SERVICE HINTS continued É 3.If the fire burns well but sometimes cre-ates excessive smoke or burns slowly, it may beother part of the house or a nearby tree. The windsmoke. The top of the chimney should be at leastNOTE: A DRAFT READING OF 0.05 TO 0.06 W.C.(WATER COLUMN) IS SUGGESTED FORPROPER BURNING OF THIS STOVE.2.Do not slam the door or otherwise impact theglass. When closing doors, make sure that logs3.Do not build fires against (or that might fall4.Do not clean the glass with materials that may5.Never attempt to clean the glass while the unitis hot. If deposits are not very heavy, normal6.Never put substances which can ignite explo-cleaning products for wood stoves include, A.W.Perkins Co. (www.awperkins.com) or RutlandProducts (www.rutland.com). CAUTION: REPLACE GLASS ONLY WITH 5MMHIGH TEMPERATURE CERAMIC GLASS OFGlass Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove screw and glass clip. (See parts list3.Lift glass out from glass clip.4.Remove old gasket and clean glass.5.Replace new gasket starting at the bottom of6.Trim to length and butt ends together.7.Replace glass into door, being sure not to over-provides glass and door seal may lose itÕs resil-diately.Door Gasket Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove old door gasket and clean channel.3.Using an approved, high temperature gasket4.Starting at hinge side of door, work 3/8-inchdiameter fiberglass gasket material into chan-5.Close door and allow three to four hours for VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 13 When wood is burned slowly, it produces tarand other organic vapors which combine with ex-pelled moisture to form creosote. The creosoteof a slow-burning fire. As a result, creosote resi- cal hardware retailer. CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-TION OF WALL STUDS OR RAFTERS WHICHWERE ASSUMED TO BE A SAFE DISTANCEFROM THE CHIMNEY. IF A CHIMNEY FIRE HASOCCURRED, HAVE YOUR CHIMNEY IN-SPECTED BY A QUALIFIED EXPERT BEFOREfire in the firebox may be smothered by pour-ing a large quantity of coarse salt, baking soda, orWIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE VG650ELG MOUNTAINEERª FLOOR PROTECTOR MATERIAL CALCULATIONSThis stove has been tested for and must be installed on a floor protector with the proper Thermaltested requirements. The following instructions provide the proper information and formulas for con-1.Convert material specifications to R-value:R = 1/k x T2.Determine the R-value of proposed alternate floor protector:3.If the overall R-value of the floor protector system is equal to or greater than the floor protectorF)(mF)(m)(K)(hr)(ft)(BtuWStep 1:Convert specs to R-value.R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = RspecsStep 3: Add R-values of components to get total R-value of systemRsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 17 ration from clay liner to combustibles. The fireclay linerB.Insulated SleeveC.Ventilated ThimbleSheet steel chimney connector, minimum 24 gauge inD.Chimney Section Pass-throughan inside diameter 2-inch larger than the chimney con-chimney flue liner.CHIMNEY CONNECTOR SYSTEMS & CLEARANCES VG650ELG MOUNTAINEERª 400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 COMPANY TESTIMONY:ÒFOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVERBELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFEÓThis Vogelzang heating appliance is safe when installed properly and will provide you with yearsof service. However, always exercise good judgement when you are using this stove. You are dealing Steve Vogelzang Proprietor DO USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 1 READ ALL INSTRUCTIONS CAREFULLYBEFORE STARTING THE INSTALLATIONOR OPERATING THE STOVE. FAILURE TOFOLLOW INSTRUCTIONS MAY RESULTIN PROPERTY DAMAGE, BODILY INJURY,OR EVEN DEATH. USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! U.S. Test Standard:SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIREMAY RESULT. FOR YOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUTPERMITS, RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA. READ ALL INSTRUCTIONS CAREFULLY.1.The installation of this stove must comply2.Verify that the stove is properly installedbefore firing the stove for the first time. Af-your installation properly, you must obtain3.DO NOT store wood, flammable liquids ormanufactured home, trailer or tent5.If any parts are missing or defective, pleasenotify the dealer or manufacturer immediately.DO NOT OPERATE A STOVE THAT ISMISSING ANY PARTS!.6.Do not tamper with combustion air control7.Always connect this stove to a chimney andTHIS UNIT TO A CHIMNEY FLUE SERV-ING ANOTHER APPLIANCE.to an aluminum Type B gas vent. This is notListed Residential Type and Building Heat-ing Appliance Chimney. Use a 6Ó diameterchimney or larger, that is high enough to give400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 MOUNTAINEER Model VG650ELG Owners Manual (save this manual for future reference) continued on next page VG650ELG MOUNTAINEERª and in good repair. Have the chimney inspectedby the fire department or a qualified inspector.ommend a qualified inspector.10.Creosote or soot may build up in the chimneying season and clean if necessary. (See Chim-CALL THE FIRE DEPARTMENT IMME-DIATELY! 12.To prevent injury, do not allow anyone to use14.Ashes should not be allowed to accumulateabove sides of ash drawer. Dispose of ashes incooled. The ashes may be buried in the groundor picked up by a refuse collector.give off some smoke and an odor whilefire box. This should disappear after a shortas needed to clear smoke and/or odor. Paintor abuse. When installing your stove, use care 18.The walls of the firebox may become slightlydistorted after a period of use. A slight distor-tion will not affect the operation of the stove.19.If small children will be in the same room asNEVER LEAVE SMALLCHILDREN UNSUPERVISED22.While in operation, keep the feed door closedO NOT ELEVATE FIRE! Build fire directlyon the bottom of the firebox. This stove has26.For further information on using your stovesafely, obtain a copy of the National FireProtection Association (NFPA) publication,ÒUsing Coal and Wood Stoves SafelyÓ NFPANo. HS-10-1978. The address of the NFPA isBatterymarch Park, Quincy, MA 02269.NOTE: A PROFESSIONAL, LICENSED HEATINGAND COOLING CONTRACTOR MUSTBE CONSULTED IF YOU HAVE QUESTIONSREGARDING THE INSTALLATION OF THISSOLID FUEL BURNING APPLIANCE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 3 ASSEMBLY INSTRUCTIONSNOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of TOOLS AND MATERIALS REQUIRED FOR INSTALLATION foot Folding Rule or Tape Measure MATERIALS(NOTE: The following items are NOT included with your stove)listed Type HT chimney.CAUTION: STOVE IS HEAVY. MAKE SURE YOUHAVE ADEQUATE HELP AND USE PROPERSTOVE.base (#18) and pedestal top (#14) from the car-ton. (Save cardboard for further assembly.)2.Remove parts from inside stove. Parts include:3.Using the self-tapping screws provided in the5.Place pedestal side/front assembly on top ofbase. Align holes in pedestal sides with holes6.Carefully tip the pedestal base backward and7.Tip the pedestal base assembly upright. 8.Set the pedestal drawer slide (16) inside thefloor protector.10.Place pedestal top (#14) onto pedestal base as-12.Carefully position stove body (#1) onto ped-HEAVY. Make sure you have adequate helpproper lifting techniques.mounting studs and tighten securely.13.Attach rear deflector to the rear side corners of14.Attach blower assembly (#3) to back of reardeflector. NOTE: Make sure ceramic gasket isassembly..damper installation on page 6] and secure totop surface of stove using machine screws.NOTE: After installation damper must be able VG650ELG MOUNTAINEERª PIPE CONNECTOR INSTALLATION1.The crimped end of the stovepipe fits insidethe stove flue collar. Install additional pipe and3.You must have at least 18 inches of clearance4.The pipe cannot extend into the chimney flue6.It is recommended that no more than two (2)smoke spillage. Where possible, use onlycorrugated (nonadjustable) elbows. These7.The connector pipe must not pass through anspace, or floor, ceiling, wall or combustibletems & Clearances, page 17). A UL 103 HTa chimney - a house fire could result. CORRECTWRONGWRONG NOTE: STOVE PIPE IS PURCHASE, VISIT YOUR LOCAL HARDWARE,ÒLOCATING STOVEÓ PAGE 4 FOR ADDITIONALSPECIFICATIONS.DAMPER INSTALLATION 1. Remove damper from collar by pulling handle2.Attach damper gasket to bottom of collar.3.Position collar onto hole in stove top and align4.Secure the collar to stove with bolts and nuts5.Install damper on angle into collar as shown indamper and out the opposite side of collar.NOTE: After installation, damper must be able VG650ELG MOUNTAINEERª Fig. 8 - Chimney Construction Through Roof Through Masonry WallMANUFACTURED CHIMNEYREFER TO CHIMNEY AND CHIMNEYCONNECTOR MAKERÕS INSTRUCTIONSFOR INSTALLATION AND USE.HT. Chimney made to this listing is High Tem-chimney from only one manufacturer. Never mixmanufacturerÕs stated requirements and clearances.Use the chimney manufacturerÕs attic guards, roofWhen using a pre-existing chimney, have itÕsters, hardware stores, and HVAC supply stores.tion on-line. See, www.duravent.com,www.selkirkinc.com, or www.mtlfab.com.VENTING TO EXISTING FIREPLACEexisting fireplace for stove use. Usually, safe con-more work than using a prefabricated chimney. The Continued on next page VG650ELG MOUNTAINEERª OPERATING INSTRUCTIONSWOOD FUEL ONLY!burning efficiency. Wood should be stored in a dry,NOTICE: USE SOLID WOOD MATERIALS ONLY.FLUIDS. DO NOT USE COAL THIS STOVE ISNOT DESIGNED TO ACCOMMODATE THE AIRFLOW (DRAFT) NECESSARY TO PROPERLYELEVATE FIRE OR USE GRATES OR AND-IRONS. BUILD FIRE DIRECTLY ON BOTTOM OF1.Open draft damper fully to provide maximum2.Open the feed door and place several wads of3.Lay small stacks of kindling on the paper to4.Light the paper and kindling, close the doorand secure tightly.5.Add fuel after fire is burning briskly. Use careDO NOT STORE WOOD ON FLOOR PROTEC-OR, UNDERNEATH STOVEPIPE OR ANY-FROM COMBUSTIBLE SURFACES SPECIFIEDFOR THIS STOVE.OVERFIRING MAY CAUSE A HOUSE FIRE.YOU ARE OVERFIRING IF A UNIT OR CHIMNEYCONNECTOR GLOWS RED.OPERATING SAFETY PRECAUTIONS1.NEVER OVERFIRE THIS STOVE BY BUILD-ING EXCESSIVELY HOT FIRES AS A HOUSE/BUILDING FIRE MAY RESULT. YOU ARE OVER-FIRING THE STOVE IF UNIT OR STOVEPIPEBEGINS TO GLOW OR TURN RED.2.NEVER BUILD EXTREMELY LARGE FIRESIN THIS TYPE OF STOVE AS DAMAGE TO THESTOVE OR SMOKE LEAKAGE MAY RESULT3.ON MODELS WITH GLASS DOOR, DO NOTBUILD FIRE TOO CLOSE TO GLASS.4.UNIT IS HOT WHILE IN OPERATION. KEEPCHILDREN, CLOTHING, AND FURNITURECONTACT MAY CAUSE SKIN BURNS. DONOT TOUCH THE STOVE AFTER FIRING UNTILPROVIDE AIR INTO THE ROOM FORINSPECT STOVEPIPE EVERY 60 DAYS.REPLACE IMMEDIATELY IF STOVEPIPE ISRUSTING OR LEAKING SMOKE INTO THE 6.Secure and seal the damper in the closed posi-or furnace cement. Also check to see if theit is closed and sealed as well. A leaky cleanoutwill greatly reduce draft efficiency.the National Fire Protection Association (NFPA)and request a copy of the latest editions of NFPAStandard 211 and NFPA Standard 908. Their Battery March Park, Quincy, MA 02269. LAR FLAMMABLE LIQUIDS TO START ORÒFRESHEN-UPÓ A FIRE IN THE STOVE.KEEP ALL FLAMMABLE LIQUIDS,ESPECIALLY GASOLINE, OUT OF THEVICINITY OF THE HEATER Ñ WHETHER IN USEOR IN STORAGE. VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 11 6.Close the door and secure tightly.Adjust the draft damper control. The moreclosed the slower the fire will burn. The more8.Do not overfire the stove.stead of piling large quantities of fuel at one time.occur in the chimney.1.Always open draft damper before opening thefeed door.2.When adding fuel be careful not to smothermodels with glass door.3.Close the feed door and secure tightly.4.Adjust the draft damper control.Empty ashes regularly. Do not allow ashes7.Do not overfire the stove.CAUTION: DO NOT OVERFIRE APPLIANCE.YOU ARE OVERFIRING IF THE CHIMNEYCONNECTORS OR STOVE GLOWS RED.CLOSE THE DOOR AND SHUT FLUE DAMPERIMMEDIATELY TO REDUCE THE AIR SUPPLYTHE FIRE. THIS WILL SLOW DOWN THECAUTION: SLOW BURNING FIRES ANDEXTENDED USE MAY CAUSE EXCESSIVECREOSOTE BUILDUP. IGNITION OF CREO-SOTE BUILDUP OR OVERFIRING MAY CAUSEEXTREMELY HOT AND MAY IGNITESURROUNDING MATERIALS. IN CASE OF ACHIMNEY FIRE CALL THE FIRE DEPARTMENTIMMEDIATELY. OPERATING continued ÉOPERATING TIPS1.Burn with air control open for several minutesat numerous intervals throughout the day dur-over-fire the unit.2.Burn stove with air inlet control wide open forwood. This allows wood to achieve the char-BURN ONLY SEASONED WOOD. Avoidhas been dried for at least one year.4.A small fire is preferable to a large smoldering5.Establish a routine for the handling of fuel,ARNING: IN CASE OF CHIMNEY FIRE(1) CLOSE AIR INLET CONTROL (2) GET OUTOF THE HOUSE (3) CALL THE FIRE DEPART-MENT. Draft is a function of the chimney, not thestove Ñ do not expect the stove to draw. Smokethat the chimney is NOT functioning properly.1.The connector stovepipe may be pushedinto the chimney too far, stopping the draft.2.If the chimney is operating too cool, waterblock the chimney. Operate the stove at a fire level VG650ELG MOUNTAINEERª SERVICE HINTS continued É 3.If the fire burns well but sometimes cre-ates excessive smoke or burns slowly, it may beother part of the house or a nearby tree. The windsmoke. The top of the chimney should be at leastNOTE: A DRAFT READING OF 0.05 TO 0.06 W.C.(WATER COLUMN) IS SUGGESTED FORPROPER BURNING OF THIS STOVE.2.Do not slam the door or otherwise impact theglass. When closing doors, make sure that logs3.Do not build fires against (or that might fall4.Do not clean the glass with materials that may5.Never attempt to clean the glass while the unitis hot. If deposits are not very heavy, normal6.Never put substances which can ignite explo-cleaning products for wood stoves include, A.W.Perkins Co. (www.awperkins.com) or RutlandProducts (www.rutland.com). CAUTION: REPLACE GLASS ONLY WITH 5MMHIGH TEMPERATURE CERAMIC GLASS OFGlass Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove screw and glass clip. (See parts list3.Lift glass out from glass clip.4.Remove old gasket and clean glass.5.Replace new gasket starting at the bottom of6.Trim to length and butt ends together.7.Replace glass into door, being sure not to over-provides glass and door seal may lose itÕs resil-diately.Door Gasket Replacement Procedure:Ensure appliance is not in operation and is thor-2.Remove old door gasket and clean channel.3.Using an approved, high temperature gasket4.Starting at hinge side of door, work 3/8-inchdiameter fiberglass gasket material into chan-5.Close door and allow three to four hours for VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 13 When wood is burned slowly, it produces tarand other organic vapors which combine with ex-pelled moisture to form creosote. The creosoteof a slow-burning fire. As a result, creosote resi- cal hardware retailer. CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-TION OF WALL STUDS OR RAFTERS WHICHWERE ASSUMED TO BE A SAFE DISTANCEFROM THE CHIMNEY. IF A CHIMNEY FIRE HASOCCURRED, HAVE YOUR CHIMNEY IN-SPECTED BY A QUALIFIED EXPERT BEFOREfire in the firebox may be smothered by pour-ing a large quantity of coarse salt, baking soda, orWIRING DIAGRAM - VG650ELG MOUNTAINEER STOVE VG650ELG MOUNTAINEERª FLOOR PROTECTOR MATERIAL CALCULATIONSThis stove has been tested for and must be installed on a floor protector with the proper Thermaltested requirements. The following instructions provide the proper information and formulas for con-1.Convert material specifications to R-value:R = 1/k x T2.Determine the R-value of proposed alternate floor protector:3.If the overall R-value of the floor protector system is equal to or greater than the floor protectorF)(mF)(m)(K)(hr)(ft)(BtuWStep 1:Convert specs to R-value.R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = RspecsStep 3: Add R-values of components to get total R-value of systemRsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required VGZ-025 / 100105.0VG650ELG MOUNTAINEERª / Page 17 ration from clay liner to combustibles. The fireclay linerB.Insulated SleeveC.Ventilated ThimbleSheet steel chimney connector, minimum 24 gauge inD.Chimney Section Pass-throughan inside diameter 2-inch larger than the chimney con-chimney flue liner.CHIMNEY CONNECTOR SYSTEMS & CLEARANCES VG650ELG MOUNTAINEERª 400 West 17th Streetwww.vogelzang.comPhone: 1-616-396-1911 Fax: 1-616-396-1971 COMPANY TESTIMONY:ÒFOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVERBELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFEÓThis Vogelzang heating appliance is safe when installed properly and will provide you with yearsof service. However, always exercise good judgement when you are using this stove. You are dealing Steve Vogelzang Proprietor DO USE THIS STOVE IN AMOBILE HOME, MANUFACTURED HOME, NO EXCEPTIONS! VG650ELG MOUNTAINEERª ORDERING PARTS - VG650ELG MOUNTAINEER STOVE Part No.DescriptionQty. Part No.DescriptionQty.16Pedestal Drawer Slide.................................117Pedestal Front..............................................118Pedestal Base..............................................119Hardware Pack (not shown).........................120Fire Brick Pack (only one brick shown)........121Blower Housing (only)..................................122Blower/Motor (not shown)............................123Power Cord (not shown)..............................124Cord Strain Relief (not shown).....................125Speed Control (not shown)..........................126Ceramic Fiber Gasket (not shown)..............127Screw, Glass Retainer (see diag. pg. 15)...1128Complete Door Assembly (less handle).......1Stove Body...................................................1Heat Shield..................................................1Blower Assembly F-6...................................1Flue Collar....................................................1Flue Damper................................................1Cover, Ash Cleanout....................................1Stove Door Frame........................................1Door Handle Assembly................................1Gasket, 3/8Ó dia. Fiberglass Glass Door......110Glass, Hi-Temp Ceramic..............................1Glass Retainer Brackets.............................1112Door Pins.....................................................213Ash Drawer..................................................114Pedestal Top................................................115Pedestal Side...............................................2