14.9”/ 378mm max.11.8”/ 300mm min. - PDF document

PCTE14.9”/ 378mm max.11.8”
PCTE14.9”/ 378mm max.11.8”/ 300mm min.10.0”/ 254mm max.7.3”/ 185mm min.22.8”579mm8.5”216mm20.1”511mmource Four WeightsMWESHIPPING lbskgslbskgs19146.4209.1*Includes 2.3 lbs for C-clampSource FourViewTelVictoriaVictoriaTelViaVisconti,Telolzkirchen, Holzkirchen,Tel18/F,TowerSquare,YuetBay,TelWebwww.etcconnect.comproductRev. 6.8”173mm13.3”338mm21.3”541mmATIONContinued from front page...ource Four 419LT419LT-1419EDLT19 Enhanced Denition Lens Tube complete 419EDLT-119 Enhanced Denition Lens Tube complete attern holder (A size)attern holder (B size)lass pattern holderDrop–in irisTop hatConical gel extender (requires 407CF below)7.5” Square color frame (Required for 14°, 70°, Source Four Fixture Body, Single ClutchSource Fourproducts are protected by one or more of the following * European patent application numberTo determine Candela (Cd) or Lumens (Lm) for any other HL lamp, multiply t

he Candela or Lumen value by the appropr
he Candela or Lumen value by the appropriate multiplying factor F) shown for that lamp in the table below.WattsVoltsTemp. KRT116RT196RT113RT114RT142RT143RT115RT171RT112RT117RT160RT129RT138RT154RT130RT139RT155Source Four is rated for 750W maximum. *77 Volt HL lamps are for use with ETC Dimmer Doubling technology only.hotometric data was prepared using a production xture and the rometric CCD measurement system. Fixture adjusted for cosine distribution and tested with calibrated lamp at rated voltage. All data normalized to nominal lamp lumens in accordance with IES L-73-04. Testing performed at ETC West, Hollywood, CA. All other multiplying factors extrapolated from primary test data.-63-02 format) go to www.etcconnect.com.L Specied Tolerances: Watts +/- 5%, Lumens +/-7%, Average life +/-10%, Color Temperature +/- 50KSource Fourhotometric data below is measured with an HL 750W/115V 300 hr lamp. To convert data when using any other HF. For candela or footcandle data,

multiply by the Cd F.Source Four-63-02
multiply by the Cd F.Source Four-63-02 format) may be downloaded from the ETC website.o to http://www.etcconnect.com/downloads.aspThrow To determine center beam illumination in footcandles at any throw distance, divide candela by the throw distance squared.For Field diameter at any throw distance, multiply the throw distance by .32For Beam diameter at any throw distance, multiply the throw distance by .26ource Four 19(cosine)egreeper wattBeam AngleField Angle1518egrees024681XYXYI(Flat 10%50%% illuminance foot candle or luxSource Four1 of 4Ellipsoidal SeriesSPECIFICATIONSInterchangeable lens tubes with smooth-running teon guides provide nine user-t eld angle optionsThermally insulated rear handleTwo accessory slots and a top mounted, gel frame retainerositive locking single-clutch xture bodySlot for glass or stainless steel patternsWide accessory slot with sliding cover for motorized pattern 115-240V, 50/60HzHigh temperature 3–cond

uctor 36” leads in a glass ber
uctor 36” leads in a glass ber Patented lament geometry makes for extremely efcient ATIONource FourETC Source Four are supplied with C-clamp, color frame and 3’ (96cm) leads as standardarallel-blade U-ground connectorTwo-pin and ground, 20 amp connectorrounded, 20 amp, twistlock connectorSee back page for Source Four AccessoriesECIFICATIONSRe-optimized optical system for improved photometric rojector-quality, high contrast aspheric lenshigher image quality.Faceted borosilicate reector with dichroic cold mirror coating removes greater than 90% infrared radiation (heat) and reects greater than 95% of visible lightReector secured with anti-vibration shock mountsLens(es) secured with anti-vibration shock mountsTool free, positive locking X, Y and Z lamp centering adjustments, unaffected by relampingBeam edge continually adjustable hard-to-softInterchangeable lens barrels permit selection of 5, 10, 14°, 36, and 50 EDLT lens