ACCU-CHEK Inform II Operator Training - PowerPoint Presentation

1. ACCU-CHEK Inform IIOperator TrainingACCU-CHEK, ACCU-CHEK INFORM, ACCU-CHEK PERFORMA and COBAS are trademarks of Roche. All other trademarks are the property of their respective owners.

2. 2Accu-Chek Inform II Training Outline1. Introduction – System Components3. Cleaning the meter 4. Perform a quality control test (QC) – Hands On5. Perform a patient test – Hands On6. Ranges7. View results in memory – Hands On 8. Inform II Quiz

3. 3Accu-Chek Inform II IntroductionTote Box Meter, strips, alcohol swabs controls, lancets, ref guideAccu-Chek Inform II(wireless available - Blue light in Base unit)Base Unit for automatic data transfer AND charging battery Green light when charging and sitting properly in Base unit. Red is when you first plug in Base Unit to power outlet until meter gets put in it

4. 4Accu-Chek Inform II IntroductionBarcode Scanner (Laser)Test Strip PortTouchscreen-Main menu with 3 options (finger touch only) On/Off Button

5. Back of Meter Meter re-set button (for meter freeze situation, press gently with paper clip a few seconds to re-boot)Re-Chargeable Battery PackCharging Contacts (To Base Unit) Infra-red contact to upload lot information 5

6. 6Accu-Chek Inform II Test Strips – 50/vial (replace cap immediately!) leave at Room TempExpiry date on vial is valid, opened or un-opened!Up to 10 mins to apply sampleInsert strip face up with arrows pointing in to meter!Accu-Chek Performa Control Solutions Control 1 (lo) and Control 2 (hi)Good for 3 months at Room Temp after opening (or to expiry date on vial) - write open date on vial. Blue dye- will stain clothing/fingersAccu-Chek Inform II Introduction

7. 7Accu-Chek Inform II Cleaning the Meter and Accessories with Site Approved Cleaner!

8. 8Hands On with meter!Remove meter from base unit.Press and release the On/Off button ‘Power Up’ screen appears after meter performs self-checks – date and timeNote battery life symbol in bottom right corner 4. Manually proceed to the next screen by touching symbol (happens automatically after 5 seconds)

9. 9Entering an Operator ID - Manual Entry – Hands OnTouch the symbol to backspace and delete a character entered incorrectlyTouch symbol to confirmOnce entry is complete, the main menu appearsPicture with operator ID screen-not QCOperator ID’s are not to be shared with other staff –accountable for your own ID! Turn meter off after using to prompt next user ID.(Barcode Scan if available – press icon upper right corner of screen to scan – approx 8 inches from barcode)

10. 10Accu-Chek Inform II Perform Quality Control (QC)Hands On – Run 1 level QC1. Touch ‘Control Test’2. Touch Level 1 (Lo) or Level 2 (Hi) to select the level for the test desired.QC testing is required every 24 hours and if not done, meter will be locked out until QC testing is completed. Screen will display the level of control requiredBoth level 1 and 2 must be run

11. 11Accu-Chek Inform II Perform a Quality Control (QC)- Hands On3. To select lot number: Touch the barcode symbol at top right corner of screen.Scan the barcode on the control solution vial - hold meter so scanner is 4-8 inches in front of vial barcodeScan test strip vial.NOTE: lot numbers cannot be manually entered

12. 12PASS/FAIL will appear within 5 seconds – Mandatory comment may be required for Failed QC (site dependent) Press “Cloud” icon lower left of result screen to select comment, then press “Check Mark”Take Care in positioning meter – straight up position may allow liquid in to port.4. When “Flashing Arrow” symbol appears, insert test strip into test strip port at top of meter. “Flashing Drop” symbol appears when meter is ready for QC sample. Accu-Chek Inform II Perform a QC – Hands On

13. 13Accu-Chek Inform II Perform a Patient Test – Hands OnTouch ‘Patient TestTouch ‘Check Mark’ to bypass entry. (no patient ID entry currently)

14. 14Accu-Chek Inform II Perform a Patient Test- Hands On Confirm the test strip lot:3. Touch barcode symbol top right corner of screen 4. Scan barcode on strip vial holding scanner 4-8 inches in front of vial barcode5. When “Flashing Arrow” symbol appears, insert test strip (close cap asap)Note: Test strip must ALWAYS be in meter BEFORE application of patient blood sample!!

15. 15Accu-Chek Inform II Perform a Patient Test – Hands On – Simulate with Level 1, 4, 5 or 6 Comfort Curve Linearity solutions6. For actual patient testing - make sure site is cleaned with antiseptic or soap and water, and thoroughly air dry.7. When “Flashing Drop” symbol appears, pierce site – simulate with level 1, 4, 5 or 6 Comfort Curve solution – Big vial (up to 10 minutes to apply sample)8. Wipe away first drop and apply second drop to front edge of test strip (not top) Result appears after 5 seconds! comments may be added – (site specific) press “Cloud” icon and select comments. Press “Check Mark”

16. 16Accu-Chek Inform II Ranges Critical values:“CR LO” < 2.0 mmol/L “CR HI” Adult Critical Range > 30.0 mmol/L (site dependent)Pediatric:< 17 years old results > 11.0 mmol/L Linearity Range of Meter 0.6 – 33.3 mmol/LHematocrit operating range: 10%-65% (extremes in hct will effect test result)Sample Types VenousArterialCapillaryNeonate

17. 17Accu-Chek Inform II Results ReviewQuality Control – Hands OnFrom main menu screen touch ‘Review Results’. Stored test results are displayed in a sequential list.Touch or to scroll up or down in the list. Results are grouped by date.

18. 18Interference of Galactose with Inform II Glucose System