Static Suction Head Some Important Terminologies Static Suction Lift The distance measured vertically the intake of the pump or the pump is placed above the surface of the liquid in the suction tank ID: 530586
Download Presentation The PPT/PDF document "CENTIFUGAL PUMP OPERATION" is the property of its rightful owner. Permission is granted to download and print the materials on this web site for personal, non-commercial use only, and to display it on your personal computer provided you do not modify the materials and that you retain all copyright notices contained in the materials. By downloading content from our website, you accept the terms of this agreement.
Slide1
CENTIFUGAL PUMP OPERATIONSlide2
Static Suction HeadSlide3
Some Important Terminologies
Static Suction Lift
The distance measured vertically the intake of the pump or the pump is placed above the surface of the liquid in the suction tank.
Static Suction Head
The distance measured vertically the pump is placed below the surface of the liquid in the suction tank.
Static Discharge Head
The distance measured vertically the pump is placed below the surface of the liquid in the discharge tank.
Total Static Head
The vertical distance from the surface of the liquid in the suction tank to the surface of the liquid in the discharge tank.
TSH = SSL + SDH
TSH = SDH - SSHSlide4
Velocity Head
The energy required to put the liquid in motion.
Pressure Head
The energy required to impart additional pressure on the liquid to overcome the system pressure.
Friction Head
The amount of energy required to overcome resistance in the pipes, valves and fittings.
Total Dynamic Head
The sum of velocity, pressure and friction head.
In the suction line it is called DSH
In the discharge line it is called DDH
Total Head
The total energy required to move the fluid from the suction to the discharge point. It is the sum of
static
and
dynamic
head
.Slide5
Cavitation
Definition of cavitation
Effect of cavitation on pump performance
Indication that a centrifugal pump may be cavitating
Steps that can be taken to stop pump cavitation
How to avoid pump cavitation
CENTRIFUGAL PUMP OPERATIONSlide6
Definition of cavitation
The process of the formation and subsequent collapse of vapor bubbles in a pump is called
cavitation
.Slide7
Effect of cavitation on pump performance
Three effects of pump cavitation are:
Degraded pump performance resulting in a fluctuating flow rate and discharge pressure
Excessive pump vibration
Destructive to pump internal components (damage to pump impeller, bearings, wearing rings, and seals)Slide8
Pressure profile inside a centrifugal pump.Slide9
Cavitation damage on an impeller
The shock of the imploding bubbles on the surface of the vane produces a gradual erosion and pitting which damages the impeller.Slide10
Erosion of the blades of the mixed flow pump impellerSlide11
Indication that a centrifugal pump may be cavitating
There are three indications that a centrifugal pump is cavitating.
Noise
Fluctuating discharge pressure and flow
Fluctuating pump motor currentSlide12
Steps that can be taken to stop pump cavitation
Steps that can be taken to stop pump cavitation include:
Increase the pressure at the suction of the pump.
Reduce the temperature of the liquid being pumped.
Reduce head losses in the pump suction piping.
Reduce the flow rate through the pump.(reduce NPSHR
)
Reduce the speed of the pump impeller.
(
reduce NPSH
R
)Slide13
How to avoid pump cavitation
To avoid cavitation in centrifugal pumps, the pressure of the fluid at all points within the pump must remain above saturation pressure
.
This can be achieved if:
The net positive suction head available must be greater than the net positive suction head required.
NPSHA > NPSHRSlide14
If the head losses in the pump suction piping can be reduced, the NPSH
A
will be increased.
Various methods for reducing head losses include increasing the pipe diameter, reducing the number of elbows, valves, and fittings in the pipe, and decreasing the length of the pipe.Slide15
Calculation of the net positive suction head available NPSH
ASlide16
Gas Binding
(in systems containing dissolved gases)
Gas binding of a centrifugal pump is a condition where the pump casing is filled with gases or
vapors to the point where the impeller is no longer able to contact enough fluid to function correctly.
The impeller spins in the gas bubble, but is unable to force liquid through the pump.
Effect of gas bindingThis can lead to cooling problems for the pump's packing and bearings.Slide17
To avoid gas binding
Centrifugal pumps are designed so that their pump casings are completely filled with liquid during pump operation.
Pumps in systems containing dissolved gases that are not designed to
be self-venting
should be periodically
vented manually to ensure that gases do not build up in the pump casing.Slide18
Pump Priming
Definition:
Filling the pump casing and the suction line with the liquid being pumped.
Methods of Priming
1-
If the pump is above the source of supplyclose the discharge valve and open the suction valve.Open the air vent valves to allow the air in the pump casing to escape.When water flows from the vents, they can be closed and the pump is then in primed conditions and ready for startingSlide19Slide20
2-
If the pump is above the source of supplySlide21
The priming water comes from an external source.
The discharge valve is closed and the external supply valve is opened as are the vent valves.
The water flows into the pump and into the suction line where it is prevented from escaping by the foot valve.
The water fills the suction line and then the pump casing.
When water flows from the vent valves, they and the external supply valve are closed and the pump is ready for starting.
Fig. aSlide22
The pump is primed by water which is supplied from the pump discharge line.
The discharge valve is closed and the priming valve and the air vents are opened.
Water from the discharge line fills the pump casing and the suction line.
When water flows from the vents, the vent valves and the priming valve are closed and the pump is ready for starting.
Fig. bSlide23
3- Suction Lift MethodSlide24
A separate hand operated priming pump (vacuum pump) is used.
The main pump discharge valve is closed and priming pump valve is opened.
The priming pump is operated and it exhausts air from the main pump casing and suction line causing water to fill them.
When water flows from the priming pump discharge, then the priming pump is shut and the main pump is ready for starting.Slide25
Centrifugal Pump Characteristic Curves
A vendor manual for a specific pump usually contains a curve of pump flow rate versus pump head called a pump characteristic curve
.
After a pump is installed in a system, it is usually tested to ensure that the flow rate and head of the pump are within the required specifications.Slide26Slide27
Shutoff head
is the maximum head that can be developed by a centrifugal pump operating at a
set speed.
Pump runout
is the maximum flow that can be developed by a centrifugal pump
without damaging the pump.Centrifugal pumps must be designed and operated to be protected from the conditions of pump runout or operating at shutoff head.Slide28
Flow
Head
Static
head
Pump performance curve
System curve
Pump operating pointSlide29
Centrifugal Pump Protection
Centrifugal pumps must be protected from running dead head (shutoff conditions) and runout.
One method for protecting the pump from running dead-headed is to provide a recirculation line from the pump discharge line upstream of the discharge valve, back to the pump's supply source.
Centrifugal pumps must also be protected from runout. Runout can lead to cavitation.
One method for ensuring that there is always adequate flow resistance at the pump discharge to prevent excessive flow through the pump is to place an orifice or a throttle valve immediately downstream of the pump discharge.