25 LV is a transparentlowviscosity 25 solids VOC - PDF document

1 25 LV is a transparent,low-viscosity, 25
25 LV is a transparent,low-viscosity, 25% solids, VOC- Yield /gallon per coat (m Curing only:4.9 Ð 9.84.9 Ð 9.8Dustproofing and sealing:4.9 Ð 9.84.9 Ð 9.89.8 Ð 14.69.8 Ð 14.6Renovating, dustproofing, andsealing:4.9 Ð 7.34.9 Ð 7.3Under mastic floor adhesives:9.8 Ð 14.69.8 Ð 14.6Coverage rates listed areapproximations. Coverage varies withsurface profile will determine exactcoverage rate. 25 LV: Amber; dries clear Shelf Life 18 months when properly stored Store in unopened containers in a cool, clean, dryarea. Keep Kure-N-Seal 25 LV from freezing in thecontainer; do not store below 35¡F (2¡C). to Use LOCATION ꔀInterior and exteriorꔀHorizontal and vertical TE ꔀFreshly placed and finished concreteꔀAged concrete ꔀExposed aggregate FeaturesBenefits ꔀCuring compoundEfficiently retains moisture for freshly placed concrete; ensures proper strength development; ꔀLow viscosityProvides better application at cool temperaturesꔀSealer and dustprooferMakes surfaces easier to clean and maintainꔀSemi-gloss appearanceSurfaces look newer and brighterꔀAbrasion resistantWithstands foot traffic; provides extended wearꔀCompatible with a variety of adhesivesCan be tiled or carpeted over 25 LV Low-viscosity, transparent, solvent-based, acrylic curing, sealing PRODUCT DATA Curing 03 39 00 Test Data Moisture retention, ASTM C 156applied at 300 ft Kure-N-Seal 25 LV0.38 Test requirement Drying time, hrs ASTM C 1315 25 ASTM C 1644 ꄀF (¡C)ꄀꄀ 42 42ASTM D 56 Acid and alkali resistance, No effect observed ASTM D 1308 at 1 and 16 hours UV light resistance Membrane lighter ASTM G 53 than Gardner color 3 Adhesion of tile cement, psi� 165ASTM C 1315 est results are averages obtained under laboratory conditions. Reasonable variations can be expected. ROPERTY R

2 ESULTSTEST METHODS How to Apply Surface
ESULTSTEST METHODS How to Apply Surface Preparation NEWLY PLACED CONCRETE 1.Surface must be sound and properly finished. 2.Surface is application ready when damp, but not NEWLY CURED BARE CONCRETE 1.Level any gouges. 2.Remove all dirt, dust, oil, grease, asphalt andrequired. Citrus Degreaser is excellent for3.Rinse thoroughly and allow to dry. Kure-N-Seal 25 LV may be applied to damp but not wet surfaces. AGED CONCRETE 1.Restore surface to soundness by patching,other foreign matter. Clean as required, following procedure under 1.Stir Kure-N-Seal 25 LV thoroughly before using.2.Apply a continuous, uniform film by low-applicator. For best results, use a Hudson or equivalent canister curing compound sprayer.Use a tip size of 0.8004 for water-based orstructure is ready for occupancy.4.To seal and dustproof, 2 coats must be applied. Clean Up Clean tools and equipment with Reducer 990immediately after use and while Kure-N-Seal 25 LV Drying Time ꄀF (18 to 29¡C) at 50% relativehumidity. High humidity will increase drying times.Normal traffic: overnight and gouges in the surface. If required, areas can be 25 LV to For Best Performance ꔀKure-N-Seal 25 LV may settle and must beꔀDo not thin.ꔀKeep away from heat and open flame.ꔀApplication not recommended when surfacetemperature exceeds 120¡F (49¡C).ꔀIf Kure-N-Seal 25 LV is to be applied in or near ꔀHeating Ventilation Air Conditioning (HVAC) 25 LV in or Technical Data 25 LV is an acrylic polymer resin in asolvent carrier. ꔀKure-N-Seal 25 LV is recommended for use onin Table 1.1, ACI Standard 302ꔀASTM C 309, Type 1, Class AꔀASTM C 1315, Type I, Class A (per AIMꔀCorps of Engineers CRD-C304,ꔀTor IDor IDꔀUSDA compliant for use in meat and poultry PRODUCT DATA 25 LV Do not apply Kure-N-Seal LV to theꔀ

3 Do not use on surfaces to receive concre
Do not use on surfaces to receive concreteꔀNot recommended as a release agent or whereꔀKure-N-Seal 25 LV should not be used in areasꔀAvoid excess moisture until material is fullyꔀAlthough Kure-N-Seal 25 LV is compatible with may occur. Kure-N-Seal 25 LV will highlightꔀKure-N-Seal 25 LV is considered a light-duty 25 LV.ꔀFor professional use only; not for sale to or useꔀMake certain the most current versions ofꔀProper application is the responsibility of the user. Health and Safety 25 LV LV contains solvent naphthapetroleumpetroleum, 2, 4, trimethyl Combustible liquid and vapor. May cause skin andINTENTIONAL MISUSE BY DELIBERATELYINHALING THE CONTENTS MAY BE HARMFUL ORTAL. READ MSDS AND TECHNICAL DATA GUIDE BEFOREUSING. DO NOT USE UNTIL ALL BYSTANDERSHAVE BEEN WARNED OF PRODUCT HAZARDS.KEEP AWAY FROM HEAT, FLAME AND SOURCES OFapors are heavier than air. DO NOT cutwith eyes, skin and clothing. Wash thoroughly afterotection and if the TLV is exceeded orNIOSH/MSHA approved respiratory protection in HILDREN. First Aid for at least 15 minutes. SEEK IMMEDIATE MEDICALATTENTION. In case of skin contact, wash affectedareas with soap and water. If irritation persists,SEEK IMMEDIATE MEDICAL ATTENTION. Removecauses physical discomfort, remove to fresh air. IfATTENTION. Proposition 65 defects or other reproductive harm. VOC Content 5.02 lbs/gal or 601 g/L, less water and exemptsolvents. For medical emergencies only, call ChemT1-800-424-93001-800-424-9300 PRODUCT DATA 25 LV PRODUCT DATA 25 LV BASF Construction Chemicals,LLC퀀 889 Valley Park DriveShakopee,MN,55379www.BuildingSystems.BASF.com Customer Service Technical Service For professional use only.Not for sale to or use by the general public. 2007 BASFPrinted in U.S.A. LIMITED WARRANTY NOTICE Every reasonable

4 effort is made to apply BASF exacting st
effort is made to apply BASF exacting standards both in the manufacture of our products and in the information which we issue concerning these products and their use.We ,at our election,refund the purchase price of any products proved defective.Satisfactory results depend not only upon quality products,but also upon many factorsbeyond our control.Therefore,except for such replacement or refund,BASF MAKES NO WARRANTY OR GUARANTEE,EXPRESS OR IMPLIED,INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY,RESPECTING ITS PRODUCTS,and BASF shall have no other liability with respect thereto.An11te of shipment.No claimauthorized change in the printed recommendations concerning the use of our products must bear the signature of the BASF Technical Manager.or providing such information and advice including the extent to which such information andadvice may relate to existing third party intellectual property rights,especially patent rights.In particular,BASF disclaims all CONDITIONS AND WARRANTIES,WHETHER EXPRESS OR IMPLIED,INCLUDING THE IMPLIED WARRANTIESARTICULAR PURPOSE OR MERCHANTABILITY.BASF SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL,INDIRECT OR INCIDENTINCLUDING LOSS OF PROFITSINCLUDING LOSS OF PROFITSANY KIND.BASF reservesress or further developments.It is the customerÕs responsibility and obligation to carefully inspect and test any incoming goods.Perfssshould be verified by testing and carried out only by qualified experts.It is the sole responsibility of the customer to carry out and arrange for any such testing.Reference to trade names used by other companies is neither a recommendation,nor an endorsement of any product and does not imply that similar products could not be used. Form No. Printed on recycled paper including 10% post-consumer fiber