PDF-HSE information sheet Introduction Falsework is any te

Any failure of falsework may lead to the collapse of the permanent structure This could cause injury or death to those working on or near to it as well as loss of time and money The causes of many past failures were foreseeable and could have been p. 123 It provides advice for woodworking employers It explains what the health and safety risks from wood dust are and how they can be controlled It will also help employers to ask the right questions when dealing with local exhaust ventilation LEV de It tells you how to plan and carry out the work and decide what precautions are needed It also gives advice on how to dispose of used dipwash and containers safely Before you start Competent operators Everyone involved in the dipping operation must 00 2800 3800 6500 11500 16500 SPECIALTY 2200 3400 4800 8000 13500 18000 SERVES 2x2 2025 4050 80100 SERVES 2x3 1518 30 35 6070 PLAIN 1600 2000 3600 4800 CLASSICS 6000 10000 20000 CLASSICS ONLY 3600 7000 13000 FLAVORED 2000 2600 4000 5600 SPECIALTY 700 with other Regulators. Jan Combs. HM . Inspector . of Health & Safety. Kent Delivery Group, Ashford. Health and Safety . Executive. HSE’s responsibilities. All our powers are from the HSW Act and the Regulations made under it.  Distribute to contractors  Post on HSE Notice Boards  Include in site HSE Induction. Contact. : . MSE54. . for further information or visit the . HSE Website. Learning No /0/2014.  Distribute to contractors  Post on HSE Notice Boards  Include in site HSE Induction. PDO Safety Advice. Date:. 10. th. August . 2014. Injury: Fracture of little finger. What Happen:. While . 25/10/2014 . Injury: . Fractured leg. What happened?. After offloading casing . joints (4 . at a time), off the truck on to the stack, the lifting hooks were taken off the casings, as the crane was winching in, ready to slew towards the truck for the next lift. The pelican hooks from the wire rope sling (4 x 4 with a single eye) caught on the underside of the casing joints and slide through until they caught on a piece of dunnage on the fourth layer of the stack, this caused one of the casing joints to lift and move, the IP, (who was stood on the stack), tried avoid the casing joint but couldn't, the casing joint struck the IP on his lower right leg. . LTI: Fractured finger. What happened?. . During . pulling out of hole, the . crew were . laying down . the tubing joints . on the . catwalk using cat . line when the joint became stuck. . The roustabout was standing next to the catwalk with his right hand resting on its edge and as a tubing joint came down the ramp, it jumped out of the V groove and struck his hand fracturing a finger. . :. . 25/02/14 . Injury: Fractured finger. What happened. ?. A driver was injured when he jumped up to push dunnage from his trailer he grabbed hold of the stanchion and his momentum carried the stanchion forward trapping his hand against the pipe. As a result he sustained broken and lacerated fingers.. Injury: Multiple fractures. What happened?. A . Mitsubishi Canter truck was driving behind a heavy truck that generated a large dust cloud . reducing visibility. The driver of the Canter truck pulled out . Always watch the placement of your hand. STOP the activity if anyone is approaching a suspended object. Always follow the instruction from supervisor and SOP. Date: 16-01-2015. Injury: Finger fracture . . HSE . Requirements. for . Contractors. R. eplaces. . existing Group & . branches rules and defines . 21 . requirements. HSE requirements for:. Planning and Contract Preparation. Selection of Contractors. Liz Hunter 020 3028 3369. HM Inspector of Health and Safety. elizabeth.hunter@hse.gov.uk. HSE construction health statistics* 2017-2018. 82,000 ill-health cases . Key trades affected = carpenters, joiners, general builders, M&E, plumbers. M&S : . What. are the gaps . between. the CR-GR-HSE-301 and the CR-GR-HSEQ-311?. Purpose. This Group rule defines the HSE requirements for managing technological risks throughout the entire lifecycle of an installation, from the design phase,...